Fan Drive - Disassemble
开始:
- 拆下风扇驱动装置。 请参考拆卸和组装, "风扇驱动装置 - 拆除"部分。
- 拆下将连接座 (1) 固定在风扇皮带轮轮毂 (3) 上的螺栓 (2)。 从皮带轮轮毂 (3) 上拆下连接座 (1)。
Show/hide table
图 2 g01052047 - 拆下连接座 (1) 上的 O 形密封圈 (4)。
Show/hide table
图 3 g01211377 - 将适当的吊具系缚到风扇驱动皮带轮 (5) 上。
- 拆下将风扇驱动皮带轮 (5) 固定到风扇皮带轮轮毂 (3) 上的螺栓 (6) 和垫圈。 从风扇皮带轮轮毂 (3) 上拆下风扇驱动皮带轮 (5)。 风扇驱动皮带轮 (5) 的重量约为
65 千克 (144 磅) 。Show/hide table图 4 g01211385 - 拆下将挡圈 (8) 固定在轴 (9)(未显示)上的螺栓 (7) 和垫圈。
Show/hide table
图 5 g01211389 - 从风扇皮带轮轮毂 (3) 上拆下轴承内环 (10)。
Show/hide table
图 6 g01211393 - 从轴 (9) 上拆下隔离圈 (11)。 从轴 (9) 上拆下风扇皮带轮轮毂 (3)。
Show/hide table
图 7 g01211431 - 如图所示,用虎钳夹住风扇皮带轮轮毂 (3)。 使用黄铜冲子将唇形密封件 (12)(未显示)和轴承内环(未显示)拆下。
Show/hide table
图 8 g01211480 - 使用黄铜冲子从风扇皮带轮轮毂 (3) 上拆下轴承外圈 (13)。
Show/hide table
图 9 g01211483 - 如图所示,再使用虎钳夹住风扇皮带轮轮毂 (3)。 使用黄铜冲子拆下轴承外圈 (14)。
Show/hide table
图 10 g01211485 - 从轴 (9) 上拆下衬套 (15)。
Show/hide table
图 11 g01211490 - 拆下将轴(未显示)固定在支架组件 (17) 上的螺栓 (16) 和垫圈。 从支架组件 (17) 上拆下轴(未显示)。
Show/hide table
图 1 | g01211375 |
Caterpillar Information System:
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
3116 Truck Engine Walk-Around Inspection
3608 Engine Air Lubricator - Remove and Install
3116 Truck Engine Fuel Tank Water and Sediment - Drain
G3500 Engines Flywheel - Remove and Install
3406E and 3456 Generator Set Engines Engine Oil Pan
3116 Truck Engine Fuel Inlet Screen - Clean/Inspect/Replace
G3606 and G3608 Engines Air Silencer - Remove and Install
3116 Truck Engine Fuel Injection Timing - Check
G3500B Engines Overhaul (Top End)
G3500B Engines Overhaul (Major)
G3500 Engines Flywheel Housing - Install
G3500 Engines Vibration Damper - Remove and Install
G3606 and G3608 Engines Air Valve - Remove and Install
G3606 and G3608 Engines Generator - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Sequence Valves - Remove and Install
120H and 135H Motor Graders Hydraulic and Steering System Gerotor Motor (Circle Drive)
3406E and 3456 Generator Set Engines Flywheel Housing
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
G3500 Engines Engine Oil Pan - Remove
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Fan Drive - Assemble
G3500 Engines Engine Oil Pan - Install
G3606 and G3608 Engines Air Inlet Elbow - Remove and Install
G3500B Engines Fuel Metering Valve Screen - Check