Accessory Drive (Front) - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0520 | 冲头总成 | 1 |
B | 482-7518 | 冲头总成密封件的安装 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 使用工具 (A) 和合适的压具在轴 (6) 上安装衬套 (14)。 衬套 (14) 必须与轴 (6) 平齐安装,容差为 ±
0.5 mm (0.020 inch) 注: 固定轴 (6) 的同时,对衬套施加
271 N·m (200 lb ft) 的扭矩时衬套 (14) 不得滑动。Show/hide table图 2 g01255150 - 将轴承中的机油孔与前适配器组件 (9) 中的机油孔对齐。 使用工具 (A) 和合适的压具在前适配器组件 (9) 上安装轴承 (11)。 安装后,轴承中的孔必须为
75.0 ± 0.055 mm (2.95 ± 0.0020 inch) 。 - 在前适配器组件 (9) 上安装 O 形密封圈 (12) 和 (13)。
Show/hide table
图 3 g01255149 - 将清洁的发动机机油涂在轴承上,并在前适配器组件 (9) 上安装轴 (6)。
- 安装固定垫圈 (10) 和螺栓。
注: 之后的机型有两个固定垫圈。
Show/hide table图 4 g01255146 - 在轴 (6) 上放置齿轮 (8) 并安装螺栓 (7)。
Show/hide table
图 5 g01255143 - 将轴承上的机油孔与后适配器组件 (1) 中的机油孔对齐。 使用工具 (A) 和合适的压具在后适配器组件 (1) 上安装轴承 (5)。 安装后,轴承中的孔必须为
75.0 ± 0.055 mm (2.95 ± 0.0020 inch) 。 - 使用工具 (B) 将密封件 (4) 安装到后适配器组件 (1) 中。 确保密封件的唇形部位对着轴承。
Show/hide table
图 6 g00906726 - 将 O 形密封圈 (2) 和 (3) 安装到后适配器组件 (1) 上。 将清洁的发动机机油涂到 O 形密封圈上。
Show/hide table
图 1 | g06095594 |
结束:
- 安装附件驱动器 (前)。 参考拆解和组装, "附件驱动器(前)- 安装"。
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 General Testing and Adjusting Information
3176C and 3196 Industrial Engines Maintenance Interval Schedule
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft - Remove
3512B and 3516B Engines Engine Design
3512B and 3516B Engines Engine Design
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Rear) - Install
G3500 Engines Accessory Drive (Front) - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Engine Oil Filter Base
3116 Truck Engine Auxiliary Engine Brakes
G3500 Engines Accessory Drive (Front) - Remove
3304B and 3306B Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3304B and 3306B Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Visual Inspection
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Water Pump
3508, 3512 and 3516 Generator Set Engines Crankshaft Rear Seal and Wear Sleeve - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Operational Checks
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Pump - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Belt Tensioner
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Hydraulic System Pressure - Release
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install - 3003 Engines
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Nozzles - Remove - 3003 Engines
320B, 320B L and 320B N Excavators Track Adjustment - Adjust