Engine Design
Show/hide table
图 1 | g00293349 |
气缸和气门的位置 (A) 进气门 (B) 排气门 |
气缸数和气缸布置 ... 60 度 V 型 12 缸
每气缸气门数 ... 4
排量 ... 58.5 L (3570 cu in)
缸径 ... 170 mm (6.7 in)
冲程 ... 215 mm (8.5 in)
压缩比 ... 15.5:1
燃烧方式 ... 直喷式
从飞轮端观看曲轴时,曲轴沿以下方向旋转。 ... 逆时针
点火顺序(喷油顺序)
标准转动 CCW ... 1, 12, 9, 4, 5, 8, 11, 2, 3, 10, 7, 6
反向旋转 CW ... 1, 4, 9, 8, 5, 2, 11, 10, 3, 6, 7, 12
气门间隙
进气 ... 0.50 mm (0.020 in)
排气 ... 1.00 mm (0.040 in)
注: 发动机的前端是与发动机飞轮端相对的发动机的另一端。 发动机的左、右侧是从发动机飞轮端来判断的。 1 号缸是发动机右侧前面的气缸。 2 号缸是发动机左侧前面的气缸。
Caterpillar Information System:
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Rear) - Install
G3500 Engines Accessory Drive (Front) - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Engine Oil Filter Base
3116 Truck Engine Auxiliary Engine Brakes
G3500 Engines Accessory Drive (Front) - Remove
3304B and 3306B Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3524B Engine for Caterpillar Built Machines Gear Group (Rear) - Install
365B Excavator Cab Air Filter (Fresh Air) - Clean/Replace
3524B Engine for Caterpillar Built Machines Gear Group (Rear) - Remove
345B Excavator Bucket Tips - Inspect/Replace
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3512B and 3516B Engines Engine Design
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft - Remove
3176C and 3196 Industrial Engines Maintenance Interval Schedule
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 General Testing and Adjusting Information
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Assemble
3304B and 3306B Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Visual Inspection
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Water Pump
3508, 3512 and 3516 Generator Set Engines Crankshaft Rear Seal and Wear Sleeve - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Operational Checks
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Pump - Install