Crankshaft - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | 138-7575     | 连接支架     | 2     |
B     | 8B-7551     | 轴承拉拔器     | 1     |
8B-7549 | 拉拔器腿     | 2     | |
3H-0465 | 压拉器板     | 4     | |
1B-4207 | 全高螺母     | 2     | |
8B-7560 | 垫板     | 1     | |
1P-0820 | 液压拉拔器     | 1     | |
9U-6600 | 手动液压泵     | 1     |
开始:
- 拆卸前壳体。 请参考解体与组装, "前壳体 - 拆卸"。
- 拆卸飞轮壳体。 请参考解体与组装, "飞轮壳体 - 拆卸和安装"。
- 拆卸发动机机油泵。 请参考解体与组装, "发动机机油泵 - 拆卸"。
- 拆下油底壳护板。 请参考解体与组装, "发动机油底壳护板 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 转动曲轴,直到曲轴齿轮 (1) 上的正时标记 "C" 与凸轮轴齿轮 (2) 上的正时标记 "C" 对准。
Show/hide table
图 1 | g00503163 |
- 从连杆上拆下连杆螺母 (4) 和连杆盖 (3) 。
Show/hide table
图 2 | g00503180 |
- 向下推动不处于上止点的活塞,以便使曲轴转到不碍事的地方。
Show/hide table
注意 |
---|
如果将活塞和连杆推入到缸套中过深,则可能损坏燃油喷嘴或活塞。 |
注: 在进气门和排气门关闭的情况下,活塞难以向下推入到气缸中。
- 从缸体中拆下主轴承盖螺栓 (5) 和主轴承盖 (6) 。
- 从后主轴承上拆下止推板 (7) 。
Show/hide table
图 3 | g00503320 |
- 如图所示,在曲轴 (8) 上安装工具 (A) 和适当的举升设备。 将曲轴从缸体中垂直向上提升出来。 3304B 曲轴的重量为 65 kg (143 lb)。 3306B 曲轴的重量为 95 kg (210 lb)。
Show/hide table
图 4 | g00503353 |
- 使用工具 (B) 从曲轴上拆下曲轴齿轮和油封承磨衬套。
Show/hide table
图 5 | g00503384 |
- 分别从主轴承盖和缸体上拆下主轴承。 分别从连杆和连杆盖上拆下连杆轴承。
注: 拆卸前在轴承和轴承盖上作上识别标记。
Caterpillar Information System:
3512B and 3516B Engines Engine Design
3512B and 3516B Engines Engine Design
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Rear) - Install
G3500 Engines Accessory Drive (Front) - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Engine Oil Filter Base
3116 Truck Engine Auxiliary Engine Brakes
G3500 Engines Accessory Drive (Front) - Remove
3304B and 3306B Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3524B Engine for Caterpillar Built Machines Gear Group (Rear) - Install
365B Excavator Cab Air Filter (Fresh Air) - Clean/Replace
3524B Engine for Caterpillar Built Machines Gear Group (Rear) - Remove
3176C and 3196 Industrial Engines Maintenance Interval Schedule
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 General Testing and Adjusting Information
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Assemble
3304B and 3306B Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Visual Inspection
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Water Pump
3508, 3512 and 3516 Generator Set Engines Crankshaft Rear Seal and Wear Sleeve - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Operational Checks
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Pump - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Belt Tensioner
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Hydraulic System Pressure - Release