Engine Oil Filter Base
发动机安装式底座
Show/hide table
 | |
| 图 1 | g00291396 |
典型实例 | |
(1) 9L-9188 弹簧 位于滤清器旁通阀内：
- 外径 ... 11.2 mm (0.44 in)
- 自由长度 ... 57.9 mm (2.28 in)
- 组装后的长度 ... 43.2 mm (1.70 in)
- 组装长度上的负载 ... 15.6 ± 1.3 N (3.50 ± 0.30 lb)
- 自由长度 ... 57.9 mm (2.28 in)
(2) 机油滤清器旁通阀必须在以下压力下打开。 ... 125 ± 30 kPa (18 ± 4.5 psi)
(3) 将 9S-3263 螺纹固定剂 涂敷在螺柱基部螺纹的最后 7.5 ± 1.5 mm (0.30 ± 0.06 in) 处。
将螺柱拧紧至以下扭矩。 ... 68 ± 7 N·m (50 ± 5 lb ft)
(4) 在滤清器油封上涂敷清洁的发动机机油。 拧紧滤清器，直到密封件与底座接触。 在密封件接触到底座后，转动滤清器 270 度。
远程安装式底座
Show/hide table
 | |
| 图 2 | g00587647 |
典型实例 | |
Show/hide table
 | |
| 图 3 | g00587684 |
A-A 视图 | |
(1) 将螺母拧紧至以下扭矩。 ... 150 ± 20 N·m (111 ± 15 lb ft)
(2) 过滤后的机油
(3) 未经过滤的机油
Caterpillar Information System:
3116 Truck Engine Auxiliary Engine Brakes
G3500 Engines Accessory Drive (Front) - Remove
3304B and 3306B Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3524B Engine for Caterpillar Built Machines Gear Group (Rear) - Install
365B Excavator Cab Air Filter (Fresh Air) - Clean/Replace
3524B Engine for Caterpillar Built Machines Gear Group (Rear) - Remove
345B Excavator Bucket Tips - Inspect/Replace
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Exhaust Elbow
G3500 Engines Crankcase Breather - Remove and Install
3054 and 3056 Industrial and Generator Set Engines Alternator and Regulator
3116 Truck Engine Engine Operation
G3500 Engines Accessory Drive (Front) - Install
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Rear) - Install
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Disassemble
3512B and 3516B Engines Engine Design
3512B and 3516B Engines Engine Design
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft - Remove
3176C and 3196 Industrial Engines Maintenance Interval Schedule
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 General Testing and Adjusting Information
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Assemble
3304B and 3306B Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Visual Inspection
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Water Pump