Gear Group (Rear) - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
B | FT-1342 | 导向螺栓 | 2 |
C | 1P-0524(1) | 驱动板 | 1 |
D | 1P-0513(1) | 驱动板 | 1 |
Show/hide table
(1) | 1P-0520 起子总成的零件 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 后齿轮总成和飞轮壳有多种可能配置。 以下程序演示了典型示例。
- 将先前拆下的定位销 (23) 安装到凸轮轴内。
Show/hide table
图 2 g00587666 典型实例 - 将凸轮轴齿轮 (22) 安装定位到凸轮轴上。 安装四个螺栓 (21)。
Show/hide table
图 3 g01712733 - 将 O 形密封圈安装到齿轮 (20A) 上。
- 利用干净的机油轻轻润滑曲轴端部的密封。
- 将工具 (B) 安装在曲轴中。 安装齿轮 (20A)。
- 采用以下程序装配平衡齿轮 (12)。
- 将环 (20)、轴承外圈 (19) 和隔套 (18) 安装到平衡齿轮 (12) 内。
注: 隔套 (18) 必须安装到齿轮 (12) 的最深处并靠住环 (20)。
Show/hide table图 5 g01712754 - 利用压具和工具 (C) 安装轴承外圈 (17)。 将轴承外圈 (17) 安装到齿轮上带有正时标记的一侧。 轴承外圈 (17) 应当接触到隔套。
Show/hide table
图 6 g00587608 典型实例 - 将轴承 (16)、隔套 (15)、轴承 (14) 和轴 (13) 安装到齿轮 (12) 中。
Show/hide table图 4 g01717018 - 将环 (20)、轴承外圈 (19) 和隔套 (18) 安装到平衡齿轮 (12) 内。
- 采用步骤 6 内的程序装配惰轮 (11)。
Show/hide table
图 7 g00587895 典型实例 - 将惰轮 (11) 和平衡齿轮 (12) 定位到飞轮壳上。 确保轴 (10) 内的机油孔与飞轮壳内的小孔对齐。
注: 安装平衡齿轮 (12),使正时标记面向飞轮壳。
- 安装螺栓 (9)。
- 采用以下步骤装配适配器组件 (1)。
- 安装先前拆下的轴承座圈 (8)。 将座圈 (8) 安装到适配器组件 (1) 中,使座圈接触沉孔。
Show/hide table
图 9 g00586907 典型实例 - 将环 (6)、螺栓 (5) 和 O 形密封圈 (7) 安装到适配器组件 (1) 上。
Show/hide table
图 10 g01712644 - 将轴承 (3) 加热到
135 °C (275 °F) 大约 30 分钟。 - 将轴承 (3) 安装到齿轮 (2) 上,直到轴承接触沉孔。
Show/hide table
图 11 g00588013 典型实例 - 将齿轮 (2) 和轴承安装到适配器组件 (1) 中。
Show/hide table
图 12 g01712873 - 利用压具和工具 (D) 将轴承 (4) 安装到适配器组件 (1) 中。 安装轴承,直到轴承接触到沉孔。
Show/hide table图 8 g00586910 典型实例 - 安装先前拆下的轴承座圈 (8)。 将座圈 (8) 安装到适配器组件 (1) 中,使座圈接触沉孔。
Show/hide table
图 1 | g00587668 |
典型实例 |
结束:
- 安装飞轮壳。 请参阅拆解和组装, "飞轮壳体 - 拆卸和安装"。
Caterpillar Information System:
G3500 Engines Accessory Drive (Front) - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Engine Oil Filter Base
3116 Truck Engine Auxiliary Engine Brakes
G3500 Engines Accessory Drive (Front) - Remove
3304B and 3306B Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3524B Engine for Caterpillar Built Machines Gear Group (Rear) - Install
365B Excavator Cab Air Filter (Fresh Air) - Clean/Replace
3524B Engine for Caterpillar Built Machines Gear Group (Rear) - Remove
345B Excavator Bucket Tips - Inspect/Replace
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Exhaust Elbow
G3500 Engines Crankcase Breather - Remove and Install
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Disassemble
3512B and 3516B Engines Engine Design
3512B and 3516B Engines Engine Design
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft - Remove
3176C and 3196 Industrial Engines Maintenance Interval Schedule
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 General Testing and Adjusting Information
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Assemble
3304B and 3306B Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Visual Inspection
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Water Pump
3508, 3512 and 3516 Generator Set Engines Crankshaft Rear Seal and Wear Sleeve - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Glow Plugs - Remove and Install