Rotator Oil Flow - Test
Show/hide table
| Required Tools | A | |
| (1) | 6V-8398 O-Ring Seals | 2 |
| (2) | 6V-8944 O-Ring Reducer | 2 |
| (3) | 6V-8557 Face Seal Nut | 2 |
| (4) | 5K-9090 O-Ring Seals | 2 |
| (5) | 8T-7813 Adapters | 2 |
| (6) | 7M-8485 O-Ring Seals | 2 |
| (7) | 9U-7446 Flange Adapters | 2 |
| (8) | 1P-4579 Flanges | 4 |
| (9) | 8T-8919 Bolts | 8 |
| (10) | 8T-4223 Hard Washers | 8 |
| (11) | 4J-0524 O-Ring Seals | 2 |
| (12) | 4C-9675 Hydraulic Flow Tester | 1 |
- Install tooling (A) to fittings (13) and (14) .
Show/hide table
 | |
| Illustration 1 | g00536078 |
Show/hide table
 | |
| Illustration 2 | g00486573 |
- Start the machine. Run the machine at high idle until the hydraulic oil reaches normal operating temperature.
- Rotate the Pulverizer to the right. Record the flow meter reading.
- Rotate the Pulverizer to the left. Record the flow meter reading.
- The flow meter reading should be 20 L/min (5 US gpm).
- Refer to the Testing and Adjusting procedures of the machine if the oil flow is incorrect.
Caterpillar Information System:
Disassembly And Assembly Of The Napier NA 297 Turbocharger{1052} Disassembly And Assembly Of The Napier NA 297 Turbocharger{1052}
P16, P20, P25, P28, P40 and P60 Pulverizers Relief Valve (Pulverizer) - Test and Adjust
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 269 FMI 4 Sensor Power Supply Voltage Below Normal - Test
3306C Truck Engine Pistons and Connecting Rods - Assemble
P16, P20, P25, P28, P40 and P60 Pulverizers Rotator Cycle - Time
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Cylinder Cycle - Time
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 269 FMI 3 Sensor Power Supply Voltage Above Normal - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 268 FMI 2 EMCP Electronic Control (Generator Set) Incorrect Signal - Test
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold
P16, P20, P25, P28, P40 and P60 Pulverizers Relief Valve
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 248 FMI 9 CAT Data Link Abnormal Update - Test
P16, P20, P25, P28, P40 and P60 Pulverizers Rotator Motor
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Cylinder Oil Flow - Test
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 333 FMI 3 Alarm Module Control Voltage Above Normal - Test
3406E On-Highway Engine Air Compressor - Remove and Install
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 333 FMI 4 Alarm Module Control Voltage Below Normal - Test
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 336 FMI 2 Switch (Engine Control) Incorrect Signal - Test
3600 Heavy Fuel Engines Derating Strategy
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 334 FMI 3 Spare Output Voltage Above Normal - Test
3306C Truck Engine Connecting Rod Bearings - Install
3306C Truck Engine Connecting Rod Bearings - Remove
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 334 FMI 4 Spare Output Voltage Below Normal - Test
3406C (PEEC III) Truck Engine Shutoff Solenoid
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 442 FMI 12 Generator Fault Relay Failed - Test