CID 248 FMI 9 CAT Data Link Abnormal Update - Test
Show/hide table
Illustration 1 | g00485981 |
System Schematic For CAT Data Link |
On 3500B gensets, the GSC uses the CAT data link to communicate with the engine ECM. The CAT data link consists of two wires that connect the GSC to the engine ECM.
Procedure
The following conditions will cause a CID 248 FMI 9:
- There is a short from the wire that connects to contact "19" of the CAT data link to the battery ("B+").
- There is a short from the wire that connects to contact "20" of the CAT data link to the battery ("B+").
- There is a short from the wire that connects to contact "19" of the CAT data link to ground ("B-").
- There is a short from the wire that connects to contact "20" of the CAT data link to ground ("B-").
The GSC cannot detect an open in the circuit of the CAT data link. Troubleshoot the wiring and repair the wiring. See Testing And Adjusting, "Schematic and Wiring Diagrams".
The GSC treats a CID 248 as an alarm fault. Active alarm faults are shown on the display when the alarm codes key is pressed. Also, the ECS is in any position except the OFF/RESET position. Clear the fault from the fault log after troubleshooting is complete.
Caterpillar Information System:
P16, P20, P25, P28, P40 and P60 Pulverizers Rotator Motor
G3612 and G3616 Engines Lubrication System
P16, P20, P25, P28, P40 and P60 Pulverizers General Information
P16, P20, P25, P28, P40 and P60 Pulverizers Crusher Tooth
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Mounting
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Cylinder
G3612 and G3616 Engines Air Inlet and Exhaust System
G3612 and G3616 Engines Cooling System
3306C Truck Engine Lifter Group - Remove and Install
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test
G3500B Engines Detonation Sensor
G3500B Engines Oxygen Sensor
P16, P20, P25, P28, P40 and P60 Pulverizers Relief Valve
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 268 FMI 2 EMCP Electronic Control (Generator Set) Incorrect Signal - Test
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 269 FMI 3 Sensor Power Supply Voltage Above Normal - Test
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Cylinder Cycle - Time
P16, P20, P25, P28, P40 and P60 Pulverizers Rotator Cycle - Time
3306C Truck Engine Pistons and Connecting Rods - Assemble
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 269 FMI 4 Sensor Power Supply Voltage Below Normal - Test
P16, P20, P25, P28, P40 and P60 Pulverizers Relief Valve (Pulverizer) - Test and Adjust
Disassembly And Assembly Of The Napier NA 297 Turbocharger{1052} Disassembly And Assembly Of The Napier NA 297 Turbocharger{1052}
P16, P20, P25, P28, P40 and P60 Pulverizers Rotator Oil Flow - Test
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Cylinder Oil Flow - Test