Rotator Cycle - Time
Show/hide table
 |
Personal injury or death can result from escaping fluid under pressure. Escaping fluid under pressure, even a very small pin-hole size leak, can penetrate body tissue and cause serious injury and possible death. If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury. Always use a board or cardboard when checking for a leak. |
 |
- Move the machine with the attachment to a smooth level location.
- Conduct a good visual inspection of all hoses, fittings, and components.
- Activate the parking brake.
- Start the machine. Run the machine at high idle until the hydraulic oil reaches normal operating temperature.
- Position the Pulverizer in a centered position.
- Move the attachment control lever to the RIGHT position. Record the time in order to rotate the Pulverizer for 360 degrees.
- Position the Pulverizer in a centered position.
- Move the attachment control lever to the LEFT position. Record the time in order to rotate the Pulverizer for 360 degrees.
- The time is different for each model. The values are listed below.
P16 and P20 ... 4.4 sec
P25 and P28 ... 4.1 sec
P40 ... 4.6 sec
P60 ... 5.4 sec
- If the cycle times are not correct, refer to the Testing and Adjusting procedures of the machine and adjust the oil flow.
Caterpillar Information System:
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Cylinder Cycle - Time
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 269 FMI 3 Sensor Power Supply Voltage Above Normal - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 268 FMI 2 EMCP Electronic Control (Generator Set) Incorrect Signal - Test
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold
P16, P20, P25, P28, P40 and P60 Pulverizers Relief Valve
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 248 FMI 9 CAT Data Link Abnormal Update - Test
P16, P20, P25, P28, P40 and P60 Pulverizers Rotator Motor
G3612 and G3616 Engines Lubrication System
P16, P20, P25, P28, P40 and P60 Pulverizers General Information
P16, P20, P25, P28, P40 and P60 Pulverizers Crusher Tooth
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Mounting
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Cylinder
3306C Truck Engine Pistons and Connecting Rods - Assemble
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 269 FMI 4 Sensor Power Supply Voltage Below Normal - Test
P16, P20, P25, P28, P40 and P60 Pulverizers Relief Valve (Pulverizer) - Test and Adjust
Disassembly And Assembly Of The Napier NA 297 Turbocharger{1052} Disassembly And Assembly Of The Napier NA 297 Turbocharger{1052}
P16, P20, P25, P28, P40 and P60 Pulverizers Rotator Oil Flow - Test
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Cylinder Oil Flow - Test
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 333 FMI 3 Alarm Module Control Voltage Above Normal - Test
3406E On-Highway Engine Air Compressor - Remove and Install
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 333 FMI 4 Alarm Module Control Voltage Below Normal - Test
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 336 FMI 2 Switch (Engine Control) Incorrect Signal - Test
3600 Heavy Fuel Engines Derating Strategy
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 334 FMI 3 Spare Output Voltage Above Normal - Test