Exhaust Bypass Valve
Show/hide table
Illustration 1 | g03238979 |
Show/hide table
Specification for 6I-2667 Exhaust Bypass     | |||
Item     | Qty     | Part     | Specification Description     |
1     | 2     | 5P-9960 Bolt     | Apply 5P-3931 Anti-Seize Compound to the threads before assembly.     |
Torque to 15 ± 3 N·m (11 ± 2 lb ft). |
|||
2     | 1     | 119-5927 Shaft     | Assemble the wastegate plate to the shaft, leaving the mounting bolts loose. Then assemble the axial stop, washer, and the cover. Tighten the bolts to the standard torque. Fully close the wastegate plate and tighten the mounting bolts to the standard torque. Bend the lock ends upward to secure the bolt position. Assemble the spacer and covers assembly onto the shaft. Make sure that the shaft can be rotated freely.     |
3     | 2     | 8M-2295 Bolt     | |
4     | 1     | 102-1694 Plate     | With the wastegate plate assembled on the shaft, fully close the plate. Assemble the lever to the wastegate shaft. Assemble and adjust the connecting rod. The shaft lever is positioned at 45 degrees ± 1.5 degrees Counter Clockwise (CCW) from the horizontal centerline of the cross shaft.     |
5     | 8     | 0S-1591 Bolt     | Apply 5P-3931 Anti-Seize Compound to the threads before assembly.     |
6     | 2     | 5L-3291 Ball Bearing As     | Assemble the rod ends to provide equal thread engagement in each rod. Lubricate the fittings and orient as shown.     |
Show/hide table
Illustration 2 | g03241160 |
Show/hide table
Specification for 6I-2667 Exhaust Bypass     | |||
Item     | Qty     | Part     | Specification Description     |
1     | 1     | 8C-7321 Rod End     | Assemble the rod ends to provide equal thread engagement in each rod. Also lubricate the fittings and orient the rod as shown.     |
2     | 2     | 039-9234 Rod     | Lubricate the threads before assembly.     |
3     | -     | -     | Fully open the wastegate plate and ensure that the pointer on the actuator stops at the internal stop of the actuator (The 100 Position). Make sure that the plate does not travel below the horizontal plane of the wastegate plate. (Adjust the connecting rod to prevent the plate from going below)     |
3     | 2     | 1F-7958 Full Nut     | Torque nuts to 60 ± 12 N·m (44 ± 9lb ft)     |
4     | 1     | 8C-7315 Rod End     | Assemble the rod ends to provide equal thread engagement in each rod. Also lubricate the fittings and orient the rod as shown.     |
Show/hide table
Illustration 3 | g03243476 |
Show/hide table
Specification for 6I-2667 Exhaust Bypass     | |||
Item     | Qty     | Part     | Specification Description     |
1     | 6     | 3H-6630 Bolt     | Lubricate the threads with Loctite 242 before assembly.     |
2     | 12     | 7L-6443 High Temperature Bolt     | |
3     | 4     | 5P-2755 High Temperature Bolt     | |
4     | 18     | 0S-1595 Bolt     | |
5     | 8     | 6V-3668 Bolt     | |
Torque bolts to 100 ± 20 N·m (74 ± 15 lb ft.) |
|||
6     | 2     | 6V-8149 Nut     | Torque nuts to 100 ± 20 N·m (74 ± 15 lb ft.)     |
Caterpillar Information System:
3306C Truck Engine Turbocharger - Install
G3612 and G3616 Engines Pressure Switch
3406E, C-10 and C-12 Truck Engines Belt - Inspect
G3606 and G3608 Engines Fuel Control
3306C Truck Engine Turbocharger - Remove
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Assemble
G3612 and G3616 Engines Flexible Drive
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Disassemble
G3606 and G3608 Engines Flexible Coupling
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Install
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Remove
3306B Industrial Engine Engine Oil Cooler - Install
3306C Truck Engine Turbocharger - Disassemble
3306C Truck Engine Turbocharger - Assemble
G3606 and G3608 Engines Air Lines
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil Level - Check
3406E, C-10, C-12, C-15, C-16 Truck Engines Cylinder Head Grounding Stud - Inspect/Clean/Tighten
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil Level Gauge - Calibrate - C-10 and C-12 Engines Only
G3612 and G3616 Engines Engine Design
3306C Truck Engine Turbocharger Wastegate - Remove and Install
G3612 and G3616 Engines Engine Design
3406E, C-10 and C-12 Truck Engines Belt Tensioner - Inspect
3306C Truck Engine Exhaust Manifold - Remove and Install
3306C Truck Engine Water Temperature Regulator - Remove and Install