Air Lines
Show/hide table
 | |
| Illustration 1 | g03243991 |
Show/hide table
| Specification for 6I-2666 Air Lines Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 6I-2522 Lever | Perform this adjustment after the assembly of the stop, the choke plate, and with the actuator indicator in the CLOSED (100) position. Assemble the lever at 0 degrees (vertical) as indicated. Then adjust the rod assembly length to insure choke plate is fully closed and actuator indicator is 3.0 degrees ± 0.5 degrees. Which is indicated in view (B-B), with the actuator in the CLOSED position. |
| 2 | 4 | 6V-5095 O-Ring Seal | Lubricate the bore lightly with glycerin or approved equivalent. |
Show/hide table
 | |
| Illustration 2 | g03244117 |
Show/hide table
| Specification for 6I-2666 Air Lines Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 7X-7874 Rod End | Assemble the rod ends to provide equal thread engagement and lubricate the fittings. |
| 2 | 1 | 1S-3584 Full Nut | Torque the full nut to 25 ± 6 N·m (18 ± 4 lb ft). |
| 3 | 1 | 038-7444 Rod | Assemble the rod ends to provide equal thread engagement and lubricate the fittings. |
| Perform this adjustment after the assembly of the stop, the choke plate, and with the actuator indicator in the CLOSED (100) position. Assemble the lever at 0 degrees (vertical) as indicated. Then adjust the rod assembly length to insure choke plate is fully closed and actuator indicator is 3.0 degrees ± 0.5 degrees. Which is indicated in view (B-B), with the actuator in the CLOSED position. | |||
| 4 | 3 | 031-0214 Locking Bolt | Assemble the choke plate to the shaft, leaving the mounting bolts loose. Assemble the thrust washer's and tighten the bolts to the standard torque. Fully close the choke plate and tighten the mounting bolts to the standard torque. |
| 5 | 1 | 6I-1705 Washer | |
| 6 | 2 | 0S-1594 Bolt | |
| 7 | 1 | 3S-2713 Full Nut | Torque the full nut to 25 ± 6 N·m (18 ± 4 lb ft). |
| 8 | 1 | 7X-7875 Rod End | Assemble the rod ends to provide equal thread engagement and lubricate the fittings. |
| 9 | 1 | 6I-0728 Butterfly Plate | Assemble the choke plate to the shaft, leaving the mounting bolts loose. Assemble the thrust washer's and tighten the bolts to the standard torque. Fully close the choke plate and tighten the mounting bolts to the standard torque. |
| With the choke plate assembled on the shaft, fully close the plate. Tighten the adjusting bolt until the bolt contacts with the stop plate. Tighten the adjusting bolt an additional quarter turn and tighten the locking nut to the standard torque. | |||
| Perform this adjustment after the assembly of the stop, the choke plate, and with the actuator indicator in the CLOSED (100) position. Assemble the lever at 0 degrees (vertical) as indicated. Then adjust the rod assembly length to insure choke plate is fully closed and actuator indicator is 3.0 degrees ± 0.5 degrees. Which is indicated in view (B-B), with the actuator in the CLOSED position. | |||
Show/hide table
 | |
| Illustration 3 | g03246016 |
(A) Actuator CLOSED position. (B) Final Assembly OPEN position. (C) 3 Degrees | |
Show/hide table
| Specification for 6I-2666 Air Lines Gp | |||
| Item | Qty | Part | Specification Description |
| A | - | - | Perform this adjustment after the assembly of the stop, the choke plate, and with the actuator indicator in the CLOSED (100) position. Assemble the lever at 0 degrees (vertical) as indicated. Then adjust the rod assembly length to insure choke plate is fully closed and actuator indicator is 3.0 degrees ± 0.5 degrees. Which is indicated in view (B-B), with the actuator in the CLOSED position. |
| B | |||
| C | |||
| 1 | 1 | 1A-9579 Bolt | With the choke plate assembled on the shaft, fully close the plate. Tighten the adjusting bolt until the bolt contacts with the stop plate. Tighten the adjusting bolt an additional quarter turn and tighten the locking nut to the required torque. |
| 2 | 1 | 010-2575 Setscrew | Before assembly use Loctite 242 on the setscrew threads. |
| 3 | 1 | 6I-1704 Shaft | Assemble the choke plate to the shaft, leaving the mounting bolts loose. Assemble the thrust washer's and tighten the bolts to the required torque. Fully close the choke plate and tighten the mounting bolts to the required torque. |
Caterpillar Information System:
3306C Truck Engine Turbocharger - Assemble
3306C Truck Engine Turbocharger - Disassemble
G3606 and G3608 Engines Exhaust Bypass Valve
3306C Truck Engine Turbocharger - Install
G3612 and G3616 Engines Pressure Switch
3406E, C-10 and C-12 Truck Engines Belt - Inspect
G3606 and G3608 Engines Fuel Control
3306C Truck Engine Turbocharger - Remove
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Assemble
G3612 and G3616 Engines Flexible Drive
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Disassemble
G3606 and G3608 Engines Flexible Coupling
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil Level - Check
3406E, C-10, C-12, C-15, C-16 Truck Engines Cylinder Head Grounding Stud - Inspect/Clean/Tighten
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil Level Gauge - Calibrate - C-10 and C-12 Engines Only
G3612 and G3616 Engines Engine Design
3306C Truck Engine Turbocharger Wastegate - Remove and Install
G3612 and G3616 Engines Engine Design
3406E, C-10 and C-12 Truck Engines Belt Tensioner - Inspect
3306C Truck Engine Exhaust Manifold - Remove and Install
3306C Truck Engine Water Temperature Regulator - Remove and Install
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil and Filter - Change
3306C Truck Engine Water Pump - Remove
3306C Truck Engine Water Pump - Install