Turbocharger - Assemble
Assembly Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Check all of the parts of the turbocharger for damage. If the parts are damaged, use new parts for replacement. Refer to Special Instruction, SMHS6854, "Turbocharger Reconditioning Procedures" for more information. Also refer to Guidelines for Reusable Parts, SEBF8018 .
Show/hide table
Illustration 1 | g00471471 |
- Install new cartridge assembly (1) .
Note: Be careful not to bend the fins on cartridge assembly (1) during assembly.
- Put an alignment mark on the new cartridge assembly in the same location as the old cartridge assembly.
Show/hide table
Illustration 2 | g00471482 |
- Put cartridge assembly (1) into turbine housing (3) and align the marks.
- Install clamp (2) . Tighten clamp (2) to a torque of 14 ± 3 N·m (10 ± 2 lb ft). Tap the clamp all the way around and tighten the clamp again to a torque of 14 ± 3 N·m (10 ± 2 lb ft) .
- Place compressor housing (4) in the original position. Use the alignment marks in order to align compressor housing (4) with turbine housing (3) . Install clamp (5) . Tighten clamp (5) to a torque of 14 ± 3 N·m (10 ± 2 lb ft). Tap the clamp all the way around and tighten the clamp again to a torque of 14 ± 3 N·m (10 ± 2 lb ft) .
Show/hide table
Illustration 3 | g00471439 |
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Caterpillar Information System:
3306C Truck Engine Turbocharger - Disassemble
G3606 and G3608 Engines Exhaust Bypass Valve
3306C Truck Engine Turbocharger - Install
G3612 and G3616 Engines Pressure Switch
3406E, C-10 and C-12 Truck Engines Belt - Inspect
G3606 and G3608 Engines Fuel Control
3306C Truck Engine Turbocharger - Remove
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Assemble
G3612 and G3616 Engines Flexible Drive
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Disassemble
G3606 and G3608 Engines Flexible Coupling
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Install
G3606 and G3608 Engines Air Lines
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil Level - Check
3406E, C-10, C-12, C-15, C-16 Truck Engines Cylinder Head Grounding Stud - Inspect/Clean/Tighten
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil Level Gauge - Calibrate - C-10 and C-12 Engines Only
G3612 and G3616 Engines Engine Design
3306C Truck Engine Turbocharger Wastegate - Remove and Install
G3612 and G3616 Engines Engine Design
3406E, C-10 and C-12 Truck Engines Belt Tensioner - Inspect
3306C Truck Engine Exhaust Manifold - Remove and Install
3306C Truck Engine Water Temperature Regulator - Remove and Install
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil and Filter - Change
3306C Truck Engine Water Pump - Remove