Camshaft
Show/hide table
 | |
| Illustration 1 | g00466006 |
(1) Torque for thrust pin ... 28 ± 7 N·m (20 ± 5 lb ft)
(2) Diameter of new camshaft journals ... 74.850 ± 0.025 mm (2.9468 ± .0010 inch)
(3) Key
(4) Part number
(5) Gear
Show/hide table
 | |
| Illustration 2 | g00466107 |
(6) Camshaft lobe lift
Specified camshaft lobe lift (6)
- Exhaust lobe ... 9.550 mm (.3760 inch)
- Inlet lobe ... 11.371 mm (.4477 inch)
- Injector lobe ... 10.474 mm (.4124 inch)
- Inlet lobe ... 11.371 mm (.4477 inch)
(7) Camshaft lobe height
(8) Base circle
Specified base circle (8)
- Exhaust lobe ... 55.0 ± 0.4 mm (2.17 ± .02 inch)
- Inlet lobe ... 51.0 ± 0.4 mm (2.01 ± .02 inch)
- Injector lobe ... 52.2 ± .4 mm (2.0551 ± .02 inch)
- Inlet lobe ... 51.0 ± 0.4 mm (2.01 ± .02 inch)
To find the lobe lift, use the procedure that follows:
- Measure the camshaft lobe height (7) .
- Measure the base circle (8) .
- Subtract the base circle that is found in Step 2 from the lobe height that is found in Step 1. The difference is the actual camshaft lobe lift (6) .
Maximum permissible difference between actual lobe lift and the specified lobe lift of a new camshaft ... ± 0.13 mm (.005 inch)
Caterpillar Information System:
G3612 and G3616 Engines Magneto
3208 Marine Engine Engine Air Cleaner Element - Clean/Replace
3304B and 3306B Engines for Caterpillar Built Machines Cylinder Liner - Remove
3126 HEUI Industrial Engine Troubleshooting
Installation Of The 161-7153 Harness Assembly On The 3126B Truck Engine{1408, 4466} Installation Of The 161-7153 Harness Assembly On The 3126B Truck Engine{1408, 4466}
3208 Marine Engine Belt - Inspect/Adjust/Replace
G3606 and G3608 Engines Engine Design
3126 Truck Engine (Military) Before Starting Engine
3306C Truck Engine Engine Oil Pump - Remove
3176C and 3196 Industrial Engines Turbocharger
3208 Marine Engine Engine Air Cleaner Element (Foam) - Clean/Replace
3406E, C-10, C-12, C-15, C-16 Truck Engines Model View Illustrations
P16, P20, P25, P28, P40 and P60 Pulverizer Crusher Tooth - Rebuild
P16, P20, P25, P28, P40 and P60 Pulverizer Crusher Tooth - Replace
G3606 and G3608 Engines Magneto Drive
3304B and 3306B Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install
Removal Of Broken Head Bolts On 3176 Engines Without Removing The Aluminum Spacer Deck{1100} Removal Of Broken Head Bolts On 3176 Engines Without Removing The Aluminum Spacer Deck{1100}
3208 Marine Engine Aftercooler Drain Plug - Inspect
G3500 Engines Vibration Damper Guard
3406E Truck Engines Fuel Transfer Pump
G3612 and G3616 Engines Magneto Drive
P16, P20, P25, P28, P40 and P60 Pulverizer Bearings (Cylinder Ends) - Lubricate
3406C Engines for Caterpillar Built Machines Turbocharger
C18 Marine and Marine Generator Set Engines Camshaft