Pump Drive - Disassemble
Reference: Special Instruction, "Visual Service Procedures - Colors and Symbols" M0066576
Show/hide table
Required Tools | |||
Tools | Part Number | Part Description | Qty |
A | 5J-7910 | Bolt | 2 |
B | 1P-0510 | Driver Gp | 1 |
C | 446-9412 | Bearing Puller Assembly | 1 |
Start By:
- Remove the pump drive.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Illustration 1 | g06290057 |
Show/hide table
Illustration 2 | g06290499 |
Show/hide table
Illustration 3 | g06290542 |
Show/hide table
Illustration 4 | g06295865 |
Show/hide table
Illustration 5 | g06296594 |
Show/hide table
Illustration 6 | g06296606 |
Top Bearing Cage |
Show/hide table
Illustration 7 | g06296163 |
Show/hide table
Illustration 8 | g06296174 |
Note: The pump drive gear can fall from the housing. Retain the pump drive gear.
Show/hide table
Illustration 9 | g06296622 |
Show/hide table
Illustration 10 | g06296618 |
Lower Bearing Cage |
Show/hide table
Illustration 11 | g06296628 |
Show/hide table
Illustration 12 | g06296634 |
Show/hide table
Illustration 13 | g06296377 |
Show/hide table
Illustration 14 | g06296385 |
Note: Support idler gear during the removal of governor control shaft.
Show/hide table
Illustration 15 | g06296395 |
Show/hide table
Illustration 16 | g06296711 |
Idler Gear |
Show/hide table
Illustration 17 | g06296713 |
Idler Gear |
Show/hide table
Illustration 18 | g06296714 |
Idler Gear |
Show/hide table
Illustration 19 | g06296719 |
Show/hide table
Illustration 20 | g06296980 |
Lower Drive Gear Use a Suitable Press |
Show/hide table
Illustration 21 | g06296982 |
Lower Drive Gear Use a Suitable Press |
Show/hide table
Illustration 22 | g06296990 |
Top Drive Gear Use a Suitable Press |
Show/hide table
Illustration 23 | g06296992 |
Top Drive Gear Use a Suitable Press |
Show/hide table
Illustration 24 | g06296997 |
Show/hide table
Illustration 25 | g06296999 |
Caterpillar Information System:
Troubleshooting Engine ECM Failure on Telehandler TL Series C {1408, 1422, 1900, 1901, 4493, 79K4} Troubleshooting Engine ECM Failure on Telehandler TL Series C {1408, 1422, 1900, 1901, 4493, 79K4}
Braking and Steering Overheating Events May Occur on Certain Command 793F Off-Highway Trucks {1365, 1380, 4250, 4300, 4346} Braking and Steering Overheating Events May Occur on Certain Command 793F Off-Highway Trucks {1365, 1380, 4250, 4300, 4346}
A New Water Pump is Now Used on Certain C9.3 Machine Engines {1361} A New Water Pump is Now Used on Certain C9.3 Machine Engines {1361}
Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553} Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553}
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Isolation Mounts - Inspect/Replace - Primary ECM
Regulatory Compliance Information Radio Detection and Ranging (Radar) - C5 Radar - If Equipped
797 Transmission Planet Shaft Plug Removal, Clean Planet Shaft Lube Passages and Install New Plug Procedures {0599, 0700, 0722, 3160} 797 Transmission Planet Shaft Plug Removal, Clean Planet Shaft Lube Passages and Install New Plug Procedures {0599, 0700, 0722, 3160}
24 Motor Graders Engine Supplement Muffler - Remove and Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Centrifugal Oil Filter - Assemble
24 Motor Grader Power Train Torque Converter - Assemble
559D and 579D Knuckleboom Loader Machine Systems Hydraulic Tank - Remove and Install
785G Off-Highway Truck Machines Systems Gear Pump (Brake Cooling) - Remove and Install
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Relief Valve (Torque Converter Outlet)
New VIMSpc Software Is Now Available for Certain Cat® Products {7620} New VIMSpc Software Is Now Available for Certain Cat® Products {7620}
Certain Cat® Product Link (PL) Devices May Display Duplicate Assets in Fault Code Panel {7606} Certain Cat® Product Link (PL) Devices May Display Duplicate Assets in Fault Code Panel {7606}
Certain Cat® Product Link (PL) Devices Subscribed Under Cat Daily Subscription May Report Excessively {7606} Certain Cat® Product Link (PL) Devices Subscribed Under Cat Daily Subscription May Report Excessively {7606}
Product Link (PL) Web Configuration Manager May Not Save More Than Once in a Session for Certain Cat® Product Link Assets {7606} Product Link (PL) Web Configuration Manager May Not Save More Than Once in a Session for Certain Cat® Product Link Assets {7606}
Single Configuration File May Not be Updated in Product Link (PL) Web or Dealer Service Portal (DSP) on Certain Cat® Product Link Assets {7606} Single Configuration File May Not be Updated in Product Link (PL) Web or Dealer Service Portal (DSP) on Certain Cat® Product Link Assets {7606}
559D and 579D Knuckleboom Loader Machine Systems Piston Motor (Swing Drive) - Remove and Install
CB13, CB15, and CB16 Asphalt Compactors Machine Systems Support (Cab) - Remove and Install
559D, 579D Knuckleboom Loader System Pressure Release
CB13, CB15, and CB16 Asphalt Compactors Machine Systems Cab - Remove and Install
PM820, PM822, and PM825 Cold Planer Ventilation Inlet Ducts - Inspect/Clean
PM310, PM312, and PM313 Cold Planer Camera - Clean/Adjust