Make sure that all the safety messages are legible. Clean the safety messages or replace the safety messages if you cannot read the words. Replace the illustrations if the illustrations are not visible. When you clean the safety messages, use a cloth, water, and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety message. Loose adhesive will allow the safety message to fall.
Replace any safety message that is damaged, or missing. If a safety message is attached to a part that is replaced, install a safety message on the replacement part. Any Caterpillar dealer can provide new safety messages.
Illustration 1 | g06045699 |
Illustration 2 | g06045920 |
Illustration 3 | g06045924 |
This safety message is located in the cab on the right side window and also on the engine.
Illustration 4 | g01370904 |
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Caterpillar dealer for replacement manuals. Proper care is your responsibility. |
This safety message is located in the cab on the right side window.
Illustration 5 | g01370917 |
This machine is equipped with a Caterpillar Product Link communication device. When electric detonators are used, this communication device should be deactivated within In cases where the type of Product Link module cannot be identified, Caterpillar recommends that the device be disabled no less than |
Refer to Operation and Maintenance Manual, "Product Link" for further information.
If equipped, this safety message is located in the cab on the right side window.
Illustration 6 | g01382703 |
Crushing Hazard! Certain machine front linkage combinations (boom, stick, quick coupler, work tool) may require keeping the work tool away from the cab during operation. Personal injury or death may result if the work tool contacts the cab during operation. |
If equipped, this safety message is located in the cab on the right side window.
Illustration 7 | g01373971 |
Crushing Hazard! Certain machine front linkage combinations (boom, stick, quick coupler, work tool) may require keeping the work tool away from the cab during operation. Personal injury or death may result if the work tool contacts the cab during operation. |
This safety message is located in the cab on the right side window.
Illustration 8 | g01374045 |
Electrocution Hazard! Keep the machine and attachments a safe distance from electrical power. Stay clear 3 m (10 ft) plus twice the line insulator length. Read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions and warnings will cause serious injury or death |
Refer to Operation and Maintenance Manual, "Specifications" for further information.
This safety message is located in the cab on the right side window.
Illustration 9 | g01370908 |
A seat belt should be worn at all times during machine operation to prevent serious injury or death in the event of an accident or machine overturn. Failure to wear a seat belt during machine operation may result in serious injury or death. |
Illustration 10 | g01212098 |
This warning label is located inside the cab on the right side pillar.
Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a Caterpillar dealer to determine this structure's limitations without voiding its certification. |
"Rollover Protective Structure (ROPS) and Falling Object Protective Structure (FOPS) Certification"
"The structure, when properly installed on a machine which is not altered to exceed the certification test mass meets, at the time of installation, criteria established by:SAE J396, SAE J1040 April 88, ISO 3471 1986, ISO 3471 1994, SAE J231 January 81and ISO 3449 1992LEVEL II."
Refer to Operation and Maintenance Manual, "Guards (Operator Protection)" for more information.
If equipped, this safety message is located in the cab on the right side window.
Illustration 11 | g01374035 |
Crush injury. Could cause serious injury or death. Always confirm that the quick coupler is engaged onto the pins. Read the Operator's Manual. |
Refer to Operation and Maintenance Manual, "Quick Coupler Operation" for further information.
Illustration 12 | g01371644 |
This safety message is on the front of the cab riser, behind the cab on the left front access door, and on the left rear access door.
Crushing Hazard! Stay back a safe distance. There is no clearance for a person in this area when the machine turns. Failure to follow these instructions could cause serious injury or death. |
This safety message is located in three locations on the engine hood.
Illustration 13 | g01372256 |
Engine hood and engine hood parts can be hot while engine is running or immediately after engine shutdown. Hot parts or hot components can cause burns or personal injury. Do not allow these parts to contact your skin, when engine is running or immediately after engine shutdown. Use protective clothing or protective equipment to protect your skin. |
Illustration 14 | g01384815 |
This safety message is positioned on the front access door on the left side of the machine.
Do not tilt the cab when occupied. Before tilting the cab remove all loose articles from the cab, secure all windows and emergency exits, and then close the cab and cab riser doors. Failure to do so can result in personal injury or damage to the machine. |
This safety message is positioned on the cover of the intake duct of the air cleaner. The following information is not applicable to machines that are equipped with an ether starting aid.
Illustration 15 | g01372254 |
Explosion hazard! Do not use ether! This machine is equipped with an air inlet heater. Using ether can create explosions or fires that can cause personal injury or death. Read and follow the starting procedure in the Operation and Maintenance Manual. |
Refer to Operation and Maintenance Manual, "Engine Starting" for the proper starting procedure.
This safety message is positioned on the circuit breaker panel.
Illustration 16 | g01370909 |
Explosion Hazard! Improper jumper cable connections can cause an explosion resulting in serious injury or death. Batteries may be located in separate compartments. Refer to the Operation and Maintenance Manual for the correct jump starting procedure. |
Refer to Operation and Maintenance Manual, "Engine Starting with Jump-Start Cables" for further information.
This safety message is positioned on the track adjuster on both sides of the machine.
Illustration 17 | g01076729 |
High Pressure Cylinder. Do not remove any parts from the cylinder until all of the pressure has been relieved. This will prevent possible personal injury or death. |
Refer to Operation and Maintenance Manual, "Track Adjustment - Adjust" for the adjustment procedure.
This safety message is positioned on the accumulator.
Illustration 18 | g01374065 |
This system contains high pressure gas. Failure to follow the instructions and warnings could cause an explosion, resulting in possible injury or death. Do not expose to fire. Do not weld. Do not drill. Relieve pressure before discharging. See Operation and Maintenance Manual for charging and discharging. See your Caterpillar Dealer for tools and detailed information. |
Refer to Operation and Maintenance Manual, "Equipment Lowering with Engine Stopped" for further information.
Relieve Hydraulic Tank Pressure (16)
This safety message is on top of the hydraulic tank.
Illustration 19 | g01371640 |
HYDRAULIC TANK RELIEVE TANK PRESSURE WITH ENGINE OFF BY REMOVING CAP SLOWLY TO PREVENT BURNS FROM HOT OIL. |
This safety message is on the rear of each side of the machine. This safety message is also on each side of the counterweight.
Illustration 20 | g01374060 |
Machine swings. Stay back. Crushing hazard could cause serious injury or death. |
This safety message is on the engine.
Illustration 21 | g01382725 |
Sulfuric Acid Burn Hazard may cause serious personal injury. The NOx Reduction System (NRS) may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the NRS cooler during service of the engine. The sulfuric acid will burn the eyes, skin, and clothing on contact. Always wear eye shields, rubber gloves, and protective clothing when you may come in contact with fluids that may spill from the NRS cooler. If fluid contacts an eye, immediately flush with water and seek medical help. |
This safety message is on the engine.
Illustration 22 | g01381180 |
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death. |
This safety message is located near the engine fan.
Illustration 23 | g01385578 |
Cutting Hazard! Keep hands clear of fan while engine is running. May cause serious injury or death. |
This safety message is on both sides of the stick.
Illustration 24 | g01385579 |
A crushing hazard exists when the stick and boom are in motion and when the machine is being used in object handling applications. Failure to stay clear of the stick and boom when the machine is in operation can result in personal injury or death. Stay clear of the stick and boom when the machine is in operation. |