Axle Housing and Flange - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-2320 | Combination Puller | 1 |
B | 230-7923 | Spanner Wrench As | 1 |
C | 2P-8312 | Retaining Ring Pliers | 1 |
Start By:
- Remove the drive and steering axle.
- Remove the final drive planetary.
- Loosen nut (2). Do not remove nut (2) at this time. Install Tooling (A). Remove tie rod end (1) and nut (2) . Position tie rod end (1) out of the way.
Show/hide table
Illustration 2 g01047569 - Remove bolts (5) and remove locking plate (4). Use Tooling (B) in order to remove spanner nut (3).
Show/hide table
Illustration 3 g01023074 Show/hide tableIllustration 4 g01023075 - Use a suitable pry bar and push the double U-joint toward the wheel flange. This will make the removal of retaining ring (8) easier. Use Tooling (C) and remove retaining ring (8). Remove thrust washer (7) and washer (6).
Show/hide table
Illustration 5 g01023088 - Remove ring gear (9).
Show/hide table
Illustration 6 g01023126 - Remove wheel flange (10).
Note: Bearing cone (11) will fall out of wheel flange (10) when wheel flange (10) is removed.
Show/hide tableIllustration 7 g01023130 Note: Note the order and orientation of shims (14) for assembly purposes.
- Remove bolts (12). Remove pin assembly (13) and shims (14). Remove bolts (16) and pin assembly (15).
Show/hide table
Illustration 8 g01023136 - Use a suitable lifting device in order to remove knuckle (17). The weight of knuckle (17) is approximately
56 kg (123 lb) .
Show/hide table
Illustration 1 | g01047618 |
Caterpillar Information System:
AP500F Asphalt Paver Machine Systems System Pressure - Release
AP300F Asphalt Paver Lifting and Tying Down the Machine
2015/06/23 A New Information Display is Now Used For Certain Cat® Products {7490}
816K Landfill Compactor and 815K Soil Compactor Systems Speed Sensor - Test
AP355F Asphalt Paver Roading the Machine
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Drive and Steering Axle (Front) - Remove
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Drive Shaft (Front) - Remove and Install
PL83 and PL87 Pipelayer Systems Pivot Shaft
AP355F Asphalt Paver Shipping the Machine
Bolt Inspection on 450F Backhoe Loader For Leaking Seal Kit On Hydraulic Gear Pump{5073} Bolt Inspection on 450F Backhoe Loader For Leaking Seal Kit On Hydraulic Gear Pump{5073}
AP355F Asphalt Paver Machine Cleanup Procedure
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Power Train Electronic Control System MID 027 - CID 1893 - FMI 12
R3000H Load Haul Dump Power Train Final Drive and Brake - Assemble
2015/06/04 Procedure to Install Wear Blocks on the Seat Back of Certain Load Haul Dump Machines {7312}
AP255E Asphalt Paver Engine Supplement Gear Pump (Fan Drive) - Install
797F Off-Highway Truck Field Assembly Fuel Tank - Install
AP255E Asphalt Paver Engine Supplement Radiator and Hydraulic Oil Cooler - Remove and Install
C3.8 Engines for Caterpillar Built Machines Fuel System - C3.8 Tier 4 Final EU Stage IV
740 GC, 740 Ejector, 745 Articulated Truck Power Train Transmission Planetary - Disassemble
740 GC, 740 Ejector, 745 Articulated Truck Power Train Output Transfer Gears - Disassemble
AP255E Asphalt Paver Engine Supplement Suction Fan and Gear Motor (Hydraulic Fan) - Remove
CB64B, CB66B and CB68B Asphalt Compactors Machine Systems Relief Valve (Steering) - Test and Adjust
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Axle Housing and Flange - Disassemble
AP255E Asphalt Paver Engine Supplement Suction Fan and Gear Motor (Hydraulic Fan) - Install