Procedure to Install Wear Blocks on the Seat Back of Certain Load Haul Dump Machines {7312}
- Load Haul Dump:
- R1300G (S/N: NJB1-UP)
- R1700G (S/N: SBR1-UP; XBR1-UP)
- R2900G (S/N: JLK1-UP)
- R3000H (S/N: RCM1-UP)
Description of Change:
Show/hide table
Illustration 1 | g03842639 |
Typical suspension seat (1) 186-9722 Wear Block |
When installing a replacement suspension seat a 186-9722 Wear Block must be installed to prevent wear on the seat back.
Adaptable To:
Show/hide table
Install with Wear Block     | |
Part Number     | Description     |
318-7604     | Suspension Seat Gp     |
295-4990     | Suspension Seat Gp     |
295-5002     | Suspension Seat Gp     |
313-9848     | Suspension Seat Gp     |
245-1485     | Suspension Seat Gp     |
Refer to the following procedure in order to install the 186-9722 Wear Block on the seats listed in Table 1.
Procedure to install the Wear Block
Show/hide table
Parts Required     | ||
Qty     | Part Number     | Description     |
1     | 186-9722     | Wear Block     |
2     | 5P-7921     | Washer Head Screw     |
Show/hide table
Illustration 2 | g03842638 |
Standard seat (B) 75 ± 0.8 mm (2.95 ± 0.03 inch) (C) Diameter 4.7 mm (0.185 inch) (D) 10 ± 2 mm (0.4 ± 0.08 inch) |
Show/hide table
Illustration 3 | g03842637 |
Tee Seat (F) 75 ± 0.8 mm (2.95 ± 0.03 inch) (G) Diameter 4.7 mm (0.185 inch) (H) 12.5 ± 2 mm (0.5 ± 0.08 inch) |
- Drill two holes (C) or (G) at the back of the upper section of the seat.
Refer to Illustration 2 for dimensions and location of holes for a standard seat.
Refer to Illustration 3 for dimensions and location of holes for a Tee seat.
Caterpillar Information System:
R3000H Load Haul Dump Power Train Final Drive and Brake - Assemble
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Axle Housing and Flange - Remove
AP500F Asphalt Paver Machine Systems System Pressure - Release
AP300F Asphalt Paver Lifting and Tying Down the Machine
2015/06/23 A New Information Display is Now Used For Certain Cat® Products {7490}
816K Landfill Compactor and 815K Soil Compactor Systems Speed Sensor - Test
AP355F Asphalt Paver Roading the Machine
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Drive and Steering Axle (Front) - Remove
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Drive Shaft (Front) - Remove and Install
PL83 and PL87 Pipelayer Systems Pivot Shaft
AP355F Asphalt Paver Shipping the Machine
Bolt Inspection on 450F Backhoe Loader For Leaking Seal Kit On Hydraulic Gear Pump{5073} Bolt Inspection on 450F Backhoe Loader For Leaking Seal Kit On Hydraulic Gear Pump{5073}
AP255E Asphalt Paver Engine Supplement Gear Pump (Fan Drive) - Install
797F Off-Highway Truck Field Assembly Fuel Tank - Install
AP255E Asphalt Paver Engine Supplement Radiator and Hydraulic Oil Cooler - Remove and Install
C3.8 Engines for Caterpillar Built Machines Fuel System - C3.8 Tier 4 Final EU Stage IV
740 GC, 740 Ejector, 745 Articulated Truck Power Train Transmission Planetary - Disassemble
740 GC, 740 Ejector, 745 Articulated Truck Power Train Output Transfer Gears - Disassemble
AP255E Asphalt Paver Engine Supplement Suction Fan and Gear Motor (Hydraulic Fan) - Remove
CB64B, CB66B and CB68B Asphalt Compactors Machine Systems Relief Valve (Steering) - Test and Adjust
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain Axle Housing and Flange - Disassemble
AP255E Asphalt Paver Engine Supplement Suction Fan and Gear Motor (Hydraulic Fan) - Install
PL83 and PL87 Pipelayers Engine Supplement Diesel Particulate Filter - Remove and Install - Clean Emissions Module
AP355F Asphalt Paver Parking Brake Manual Release