Tire and Rim (Front) - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 422-2352 | Jack Stand Gp | 2 |
B | 444-0526 | Manual/Hydraulic Jack | 1 |
C | 222-3123 | Penetrating Oil | 1 |
- Raise the bucket. Install cylinder lock (1).
Show/hide table
Illustration 2 g02901645 - Remove nuts (3) and fender (2). Place suitable cribbing (4) between the front axle and the frame on each side of the machine. This action will keep the front axle from oscillating.
Show/hide table
Illustration 3 g01116902 - Loosen lug nuts (5). Do not remove lug nuts (5) at this time.
Show/hide table
Illustration 4 g03104758 - Use Tooling (B) to raise the machine. Position Tooling (A) under the frame of the machine. Use Tooling (B) to lower the machine onto Tooling (A).
Show/hide table
Illustration 5 g03104759 - Attach a suitable lifting device to tire and rim (6). The combined weight of tire and rim (6) is approximately
115 kg (254 lb) . Remove lug nuts (5). Remove tire and rim (6).
Show/hide table
Illustration 1 | g02901639 |
Typical Example. |
- Install tire and rim (6) in the reverse order of removal.
- Apply one drop of Tooling (C) to the threads of lug nuts (5).
- Tighten lug nuts (5) to a torque of
460 ± 60 N·m (340 ± 44 lb ft) in a star pattern.
Caterpillar Information System:
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Drive Shaft (Rear) - Remove and Install
C3.4B Engines Engine Monitoring System
C3.4B Engines Diesel Particulate Filter Regeneration
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Drive Shaft (Front) - Remove and Install
2015/02/18 New Hose Assembly is now Used in the Power Train Oil Lines Group on Certain PL-87 Pipelayers {3016}
2014/11/20 A Procedure Is Available to Install New Cable Guides for the Cab on Certain 553C, 563C, 573C, 2570C, and 2670C Wheel Feller Bunchers {0679, 3065, 3168, 5154, 5180, 7050, 7301}
C3.4B Engines Component Location
C3.4B Engines Service Information Report
966M XE and 972M XE Wheel Loaders Battery Cable Shield - Test
C3.4B Engines General Information
330F MHPU Mobile Hydraulic Power Unit Machine System Gear Pump
950M and 962M Wheel Loaders Battery Cable Shield - Test
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Tire and Rim (Rear) - Remove and Install
MH3037 Material Handler Machine Systems Seat - Remove and Install
MH3037 Material Handler Machine Systems Hydraulic Lockout Control - Assemble
RM500B Reclaimer Mixer Power Train Case Drain Flow for Piston Motor (Propel) - Test
Installation Procedure for the 465-3300 Lines Gp - Coupler on Certain Backhoe Loaders{5057} Installation Procedure for the 465-3300 Lines Gp - Coupler on Certain Backhoe Loaders{5057}
MH3037 Material Handler Machine Systems Hydraulic Lockout Control - Disassemble
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Tie Rod (Steering)(Front) - Remove and Install
416F2, 420F2 and 430F2 Backhoe Loaders Caterpillar Approved Work Tools
MH3037 Material Handler Machine Systems Hydraulic Lockout Control - Install
MH3037 Material Handler Machine Systems Hydraulic Lockout Control - Remove
2014/12/24 A New Nut and Bearing Improve Final Drive Nut Retention on Certain 450E and 450F Backhoe Loaders {4008}
PL72 Pipelayer Track - Check/Adjust