Drive Shaft (Front) - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1U-7505 | Hydraulic Jack | 1 |
- Install Tooling (A) under guard (2). Remove bolts (1). Repeat for the other side. Use Tooling (A) to lower guard (2) to the ground. The weight of guard (2) is approximately
38 kg (85 lb) .Show/hide tableIllustration 2 g01116832 - Remove bolts (3). Discard bolts (3).
Show/hide table
Illustration 3 g01116843 - Remove bolts (5) and front drive shaft (4). Discard bolts (5).
Show/hide table
Illustration 1 | g01116830 |
Note: Removal of guard (2) is optional for clearance purposes.
- Install front drive shaft (4) in the reverse order of removal.
- Use new bolts for bolts (3) and bolts (5). Tighten bolts (3) and (5) to a torque of
28 ± 7 N·m (248 ± 62 lb in) .
- Use new bolts for bolts (3) and bolts (5). Tighten bolts (3) and (5) to a torque of
Caterpillar Information System:
2015/02/18 New Hose Assembly is now Used in the Power Train Oil Lines Group on Certain PL-87 Pipelayers {3016}
2014/11/20 A Procedure Is Available to Install New Cable Guides for the Cab on Certain 553C, 563C, 573C, 2570C, and 2670C Wheel Feller Bunchers {0679, 3065, 3168, 5154, 5180, 7050, 7301}
C3.4B Engines Component Location
C3.4B Engines Service Information Report
966M XE and 972M XE Wheel Loaders Battery Cable Shield - Test
C3.4B Engines General Information
330F MHPU Mobile Hydraulic Power Unit Machine System Gear Pump
950M and 962M Wheel Loaders Battery Cable Shield - Test
980M and 982M Medium Wheel Loaders Battery Cable Shield - Test
AP255E Asphalt Paver Propel System Machine Preparation for Testing and Adjusting
2014/11/25 A New Machine Software Gp(Brake) is Now Available For Certain 785C, 789C, 789D, 793C and 793D Large Off-Highway Trucks {7327, 7620}
2015/01/09 New Power Train Software Gp (Transmission, Chassis) Is Now Used On Certain Large Off-Highway Trucks {7620}
C3.4B Engines Diesel Particulate Filter Regeneration
C3.4B Engines Engine Monitoring System
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Drive Shaft (Rear) - Remove and Install
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Tire and Rim (Front) - Remove and Install
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Tire and Rim (Rear) - Remove and Install
MH3037 Material Handler Machine Systems Seat - Remove and Install
MH3037 Material Handler Machine Systems Hydraulic Lockout Control - Assemble
RM500B Reclaimer Mixer Power Train Case Drain Flow for Piston Motor (Propel) - Test
Installation Procedure for the 465-3300 Lines Gp - Coupler on Certain Backhoe Loaders{5057} Installation Procedure for the 465-3300 Lines Gp - Coupler on Certain Backhoe Loaders{5057}
MH3037 Material Handler Machine Systems Hydraulic Lockout Control - Disassemble
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Tie Rod (Steering)(Front) - Remove and Install
416F2, 420F2 and 430F2 Backhoe Loaders Caterpillar Approved Work Tools