Tie Rod (Steering)(Front) - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-2320 | Combination Puller | 1 |
Start By:
- Remove the front tires and rims.
- Loosen nut (1) until flush with the end of tie rod (2).
- Loosen nut (3).
- Use Tooling (A) to disconnect tie rod (2). Remove nut (1) and tie rod (2).
Show/hide table
Illustration 1 | g01117258 |
Show/hide table
Illustration 2 | g01517361 |
Note: Record the measurement from the center of nut (1) to the steering cylinder before removal in order to maintain proper alignment after installation.
- Install tie rod (2) in the reverse order of removal, adjusting to the correct length.
- Tighten nut (1) to a torque of
220 N·m (162 lb ft) . - Tighten nut (3) to a torque of
250 N·m (184 lb ft) .
- Tighten nut (1) to a torque of
Caterpillar Information System:
MH3037 Material Handler Machine Systems Hydraulic Lockout Control - Disassemble
Installation Procedure for the 465-3300 Lines Gp - Coupler on Certain Backhoe Loaders{5057} Installation Procedure for the 465-3300 Lines Gp - Coupler on Certain Backhoe Loaders{5057}
RM500B Reclaimer Mixer Power Train Case Drain Flow for Piston Motor (Propel) - Test
MH3037 Material Handler Machine Systems Hydraulic Lockout Control - Assemble
MH3037 Material Handler Machine Systems Seat - Remove and Install
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Tire and Rim (Rear) - Remove and Install
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Tire and Rim (Front) - Remove and Install
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Drive Shaft (Rear) - Remove and Install
C3.4B Engines Engine Monitoring System
C3.4B Engines Diesel Particulate Filter Regeneration
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Drive Shaft (Front) - Remove and Install
2015/02/18 New Hose Assembly is now Used in the Power Train Oil Lines Group on Certain PL-87 Pipelayers {3016}
416F2, 420F2 and 430F2 Backhoe Loaders Caterpillar Approved Work Tools
MH3037 Material Handler Machine Systems Hydraulic Lockout Control - Install
MH3037 Material Handler Machine Systems Hydraulic Lockout Control - Remove
2014/12/24 A New Nut and Bearing Improve Final Drive Nut Retention on Certain 450E and 450F Backhoe Loaders {4008}
PL72 Pipelayer Track - Check/Adjust
CB44B, CB54B, CD44B and CD54B Vibratory Asphalt Compactors Machine Electronic Control System MID 039 - CID 4580 - FMI 03
CB44B, CB54B, CD44B and CD54B Vibratory Asphalt Compactors Machine Electronic Control System MID 039 - CID 4580 - FMI 04
CB44B, CB54B, CD44B and CD54B Vibratory Asphalt Compactors Machine Electronic Control System MID 039 - CID 4580 - FMI 08
CB44B, CB54B, CD44B and CD54B Vibratory Asphalt Compactors Machine Electronic Control System MID 039 - CID 4580 - FMI 13
2015/04/08 New Software Patches Are Now Available for Cat® MineStar Fleet & Health Office v4.0.7 {7605, 7620}
2014/12/23 New Software Is Now Available For Cat ® MineStar Fleet and Health Office v4.0.7 {7605}
2015/01/29 Rework Procedure for Mounting the Improved Fuel Priming Switch Bracket on Certain 793F, 795F, and 797F Large Off-Highway Trucks {1258, 1408, 7332}