Temperature Sensor (Catalyst Inlet) - Remove and Install
拆卸步骤
- 将线束组件从温度传感器 (2) 的线束组件 (3) 上断开。
Show/hide table
图 1 | g03729002 |
- 将温度传感器 (2) 从清洁排放模块 (CEM) (1) 组件上拆下。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | Bostik 纯镍 防粘结剂     |
1     |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
- 使用工具 (A) 轻轻润滑温度传感器 (2) 的螺纹。 将温度传感器安装到 CEM (1) 。 拧紧烟尘天线至扭矩为 45 N·m (33 lb ft)。
Show/hide table
图 2 | g03729002 |
- 将线束组件连接到温度传感器 (2) 的线束组件 (3) 上。
Caterpillar Information System:
C4.4 and C7.1 Engines Water in Fuel - Test
C4.4 Engines Valve Position - Test
C7 and C9 Industrial Engines Air Shutoff - Test
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders MID 081 - CID 0688 - FMI 06
C7 and C9 Industrial Engines Engine Has Mechanical Noise (Knock)
The Brake System Pump is Failing on Certain 793F Off-Highway Trucks{5073} The Brake System Pump is Failing on Certain 793F Off-Highway Trucks{5073}
785G Off-Highway Truck Systems Relief Valve (Cylinder Crossover)
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Accumulator Charging Valve (Brake) - Remove and Install
785G Off-Highway Truck Systems Gear Pump (Brake, Front Brake Cooling, HVAC)
785G Off-Highway Truck Systems Solenoid Valve (Steering)
PL83 and PL87 Pipelayers Engine Air Filter Secondary Element - Replace
PL83 and PL87 Pipelayers Engine Air Filter Primary Element - Clean/Replace
C3.4B Engines NOx Sensor - Test
C4.4 Engines for Caterpillar Built Machines Ammonia Sensor - Remove and Install - Ammonia Sensor if Equipped
785G Off-Highway Truck Systems Steering Gear
Procedure to Install the 460-7644 Fuel Lines Gp on Certain 24M Motor Grader Engines{1274} Procedure to Install the 460-7644 Fuel Lines Gp on Certain 24M Motor Grader Engines{1274}
2015/02/19 New Front and Rear Crankshaft Seals Are Used on Certain 3500 Machine Engines {1160, 1161, 7555}
C4.4 Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install - Selective Catalytic Reduction (SCR) Temperature Sensor
Cat® Reman Injectors with Invalid Injector Trim Files {1290} Cat® Reman Injectors with Invalid Injector Trim Files {1290}
PL83 and PL87 Pipelayers Alternate Exit
2014/09/26 A New Special Instruction Is Now Available for Bypassing EGR Relay in EMCP2 Controls on Certain Generator Sets {1908, 4490, 4493}
PL83 and PL87 Pipelayers Refrigerant Dryer - Replace - If Equipped
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Transmission Hydraulic Control Operation
785G Off-Highway Truck Systems Front Wheel