Valve Mechanism Cover Base - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | 挡圈钳 | 1 |
开始:
- 拆下气门机构盖。 请参考拆解和组装, "气门机构盖 - 拆卸和安装"以了解正确步骤。
- 拆下燃油喷油管。 有关正确的步骤,请参阅拆解和组装, "燃油喷油管 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g03381182 |
- 遵循步骤 1.a 至步骤 1.f 拆下电子单体喷油器 (2) 的线束组件 (5)。
- 用深孔套筒将接头 (1) 从电子单体喷油器 (2) 上拆下。
- 切断电缆带 (3)。 将电缆带的其余部分从气门机构盖底座 (4) 上拆下。
- 将线束组件 (7) 从线束组件 (5) 上断开。
- 用工具 (A) 将卡环 (6) 从线束组件 (5) 上拆下。
- 将线束组件 (5) 从气门机构盖底座 (4 )中取出。
- 将 O 形密封圈 (8) 从线束组件 (5) 上拆下。
Show/hide table图 2 g03684236 Show/hide table图 3 g03684246 - 按相反的数字顺序松开螺栓 (9)。 参考图 3。 按相反的数字顺序松开螺栓有助于防止气门机构盖底座 (4) 变形。
- 将螺栓 (9) 从气门机构盖底座 (4) 上拆下。
- 将气门机构盖底座 (4) 从缸盖上拆下。
- 拆下密封垫 (10)。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-1860 | 挡圈钳 | 1 |
B | - | 导向螺柱 M8 × 100 mm |
2 |
C | - | 导向螺柱 M8 × 50 mm |
2 |
D | 247-5377 | 扭矩螺钉起子 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁气门机构盖底座和缸盖。 确保密封垫表面无损坏。
Show/hide table
图 4 g03684249 定位销位置 Show/hide table图 5 g03684236 Show/hide table图 6 g03684246 - 将工具 (B) 和工具 (C) 安装到缸盖上的位置 (X) 中。
- 将新密封垫 (10) 对准工具 (B) 和工具 (C)。 将密封垫安装到缸盖上。 确保密封垫朝向正确。
- 将气门机构盖底座 (4) 安置到缸盖上。
- 将螺栓 (9) 安装到气门机构盖底座 (4 )上,用手拧紧。
- 拆下工具 (B) 和工具 (C)。 将其余的螺栓 (9) 安装到气门机构盖底座 (4 )上。
- 按照图 6 所示的顺序,拧紧螺栓 (9) 至扭矩为
25 N·m (221.27 lb in) 。Show/hide table图 7 g03381182 Show/hide table图 8 g03382344 - 如有必要,安装电子单体喷油器的线束组件。 遵循步骤 8.a 至步骤 8.h 安装电子单体喷油器的线束组件。
- 确保线束组件 (5) 和气门机构盖底座 (4) 上的孔清洁且无损坏。 更换任何损坏的部件。
- 将新 O 形密封圈 (8) 安装到线束组件 (5) 上。
- 从气门机构盖底座 (4) 内侧,将线束组件 (5) 推入气门机构盖底座 (4) 中。
- 确保线束组件 (5) 上位置 (Y) 中的接头安装在垂直面。
- 使用工具 (A) 安装卡环 (6)。
- 将线束组件 (7) 连接到线束组件 (5)。
- 用一个深孔套筒将线束 (5) 连接到电子单体喷油器 (2) 上。 使用工具 (D) 拧紧接头 (1) 至扭矩为
2.4 N·m (21 lb in) 。 - 将新电缆带 (3) 安装到线束组件 (5) 上。
注: 确保电缆带符合原始设备制造商(OEM)的技术规范。
- 重复步骤 8.a 到步骤 8.h 更换其余的线束组件 (5)。
结束:
- 安装新喷油管路。 有关正确的步骤,请参阅拆解和组装, "燃油喷油管 - 安装"。
- 安装气门机构盖。 请参考拆解和组装, "气门机构盖 - 拆卸和安装"以了解正确步骤。
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
793F and 797F Off-Highway Trucks Braking System E527 High Brake Pump Command
Procedure to Upgrade Certain R2900G Load Haul Dump Machines {1408, 3101, 3159, 7000} Procedure to Upgrade Certain R2900G Load Haul Dump Machines {1408, 3101, 3159, 7000}
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Service Tool Software
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Display Modules
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Scale System
2014/07/25 New Steering Cylinder Rod is Now Used on 797F Off-Highway Trucks {4303}
2014/08/15 New Steering Cylinder Rods are Now Used on 795F AC, and 795F XQ Off-Highway Trucks {4303}
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Position Sensor (Steering Cylinder) - Set
2014/08/15 New Steering Cylinder Rods are Now Used on 793F AC, and 793F CMD Off-Highway Trucks {4303}
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Time - Check
980M and 982M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Parking Brake - Test and Adjust
C4.4 Engines for Caterpillar Built Machines Fan - Remove and Install
C4.4 Engines for Caterpillar Built Machines Fan Drive - Remove and Install
C4.4 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
329D2 and 330D2 Excavators Machine System Specifications Main Hydraulic Pump
C4.4 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
C4.4 Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C4.4 Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C4.4 Engines for Caterpillar Built Machines Relief Valve (Fuel) - Remove and Install
C4.4 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install - Aluminum and Pressed Steel Oil Pans
C4.4 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install - Cast Iron Oil Pan
14L Motor Grader Implement Electronic Control System MID 082 - CID 2214 - FMI 06
C4.4 Engines for Caterpillar Built Machines Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner