Tire and Rim - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 504-9791 | Lift Gp (60Hz)(1) | 2 |
OR | |||
504-9793 | Lift Gp (50Hz)(2) | 2 | |
B | 5P-9694 | Ratchet Hoist | 1 |
C | 425-0952 | Chock | 6 |
Show/hide table
(1) | High-Voltage (480V) Low-Voltage (240V) |
(2) | High-Voltage (400V) Low-Voltage (200V) |
Show/hide table
Servicing and changing tires and rims can be dangerous and should be done only by trained personnel using proper tools and procedures. |
Note: This procedure is being performed on the rear tires and rims. This procedure will be used to change all the tires and rims.
- Use Tooling (C) to chock the tires that are not being changed to stabilize the machine during the removal of the tires.
Show/hide table
Illustration 1 g06282372 - Position Tooling (A) under the axle as shown. Raise the machine until the tires and rims off the ground. Refer to Tool Operating Manual , NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A).
Show/hide table
Illustration 2 g01200173 - Remove all but two nuts (1) from rim (2).
Show/hide table
Illustration 3 g01214070 - Position a suitable lifting device under tire and rim (3). Attach Tooling (B) to secure tire and rim (3) to the lifting device.
- Remove two nuts (1) from the rim. Remove tire and rim (3) from the machine. The weight of tire and rim (3) is approximately
658 kg (1450 lb) .
- Install tire and rim (3) in the reverse order of removal.
- Tighten nuts (1) to a torque of
475 ± 60 N·m (350 ± 44 lb ft) .
- Tighten nuts (1) to a torque of
Caterpillar Information System:
785G Off-Highway Truck Retarding
785G Off-Highway Truck Engine Shutdown Switch
785G Off-Highway Truck Battery Disconnect Switch
C3.3B and C3.8 Engines for Caterpillar Built Machines Solenoid Valve - Test - Suction Control Valve
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Brake System Air - Purge
725C Articulated Truck Nozzle Heater Harness - Remove and Install
794 AC Off-Highway Truck Systems General Information (Suspension Cylinder System)
794 AC Off-Highway Truck Systems General Information (Automatic Lubrication System)
794 AC Off-Highway Truck Systems General Information (Fan Hydraulic System)
785G Off-Highway Truck/Tractor Electrical and Hydraulic Systems Solenoid Valve - Test
794 AC Off-Highway Truck Systems General Information (Brake System)
794 AC Off-Highway Truck Systems General Information (Hydraulic System)
2014/07/09 New Oil Tubes Are Used on 793F and 795F Off-Highway Truck Engines {1307}
785G Off-Highway Truck Braking
785G Off-Highway Truck Stopping the Machine
785G Off-Highway Truck Stopping the Engine if an Electrical Malfunction Occurs
586C Site Prep Tractor IQAN Monitoring ; Control System Customer
C1.5 and C2.2 Engines for Caterpillar Built Machines Customer Specified Parameters
C1.5 and C2.2 Engines for Caterpillar Built Machines Customer Specified Parameters Table
C1.5 and C2.2 Engines for Caterpillar Built Machines Customer Specified Parameters Worksheet
C1.5 and C2.2 Engines for Caterpillar Built Machines Acceleration Is Poor or Throttle Response Is Poor
AP655F Asphalt Paver Diesel Exhaust Fluid Tank - Flush
Procedure for Identifying and Correcting Piston Pump Group Failure on Certain 424B Backhoe Loaders{5070, 7000} Procedure for Identifying and Correcting Piston Pump Group Failure on Certain 424B Backhoe Loaders{5070, 7000}
586C Site Prep Tractor IQAN Monitoring ; Control System Engineering