Installation Of Service Replacement Thrust Plates{1203}
Usage:
All 4.75" (120.6) Bore Engines With 2 Valves Per Cylinder
Replacement thrust plates are available for the crankshaft of both the counterbored cylinder blocks, and the spacer plate cylinder blocks of the 4.75" (120.6) bore engines given above. This instruction gives a method to find which thrust plates to use, when it is necessary to make a replacement. Measure the width of the rear main bearing journal, then make reference to the chart on page 2, to find which thrust plate is needed.
NOTE: Always install the thrust plates so the words "BLOCK SIDE" are next to the cylinder block.
Measure width (A) of the rear main bearing journal of the crankshaft. Make reference to the dimensions in the chart to find the correct thrust plates to install.
Caterpillar Information System:
Installation Of 5P6595 Insert For Cylinder Liner Seat{1217} Installation Of 5P6595 Insert For Cylinder Liner Seat{1217}
Special Disassembly And Assembly Procedures For Sperry Vickers Pumps With New Type Cartridges{5055} Special Disassembly And Assembly Procedures For Sperry Vickers Pumps With New Type Cartridges{5055}
Installation And Alignment Of General Electric GE-603K Generators, GTA-15 And GTA-18 Alternators{1156, 1603} Installation And Alignment Of General Electric GE-603K Generators, GTA-15 And GTA-18 Alternators{1156, 1603}
INSTALLATION OF 7N628 GASKET SERVICE GROUP{1101, 1221} INSTALLATION OF 7N628 GASKET SERVICE GROUP{1101, 1221}
Installation Of Oversize Connecting Rod Bearings{1219} Installation Of Oversize Connecting Rod Bearings{1219}
Assembly Of Fan Drive Pulley Assemblies{1359} Assembly Of Fan Drive Pulley Assemblies{1359}
Instructions For The Use Of 5P6518 Fixture Group - Parts Reusability{1053, 1105} Instructions For The Use Of 5P6518 Fixture Group - Parts Reusability{1053, 1105}
Installation Of 4N779 And 7N6124 Fuel Injection Pump Housing Assemblies Or Fuel Injection Pump Groups{1251, 1253} Installation Of 4N779 And 7N6124 Fuel Injection Pump Housing Assemblies Or Fuel Injection Pump Groups{1251, 1253}
Use Of 3P2200 Calibration Tool Group{0650, 1250} Use Of 3P2200 Calibration Tool Group{0650, 1250}
Operation And Maintenance Of 5P6540 And 5P6542 Hose Cutoff Saw Groups{5057, 0622} Operation And Maintenance Of 5P6540 And 5P6542 Hose Cutoff Saw Groups{5057, 0622}
Installation Of 7N1754 Oil Level Gauge{1302} Installation Of 7N1754 Oil Level Gauge{1302}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704} Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Use Of The 5P7333 Tool Group For Bridge Dowel Repair{1101} Use Of The 5P7333 Tool Group For Bridge Dowel Repair{1101}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000} Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Installation Of 5N1678 Rear Power Take-Off Clutch Support Group{1007} Installation Of 5N1678 Rear Power Take-Off Clutch Support Group{1007}
Water Pump Reconditioning Using The 9N3139 Rebuild Kit And 5P7361 Tool Group{1361} Water Pump Reconditioning Using The 9N3139 Rebuild Kit And 5P7361 Tool Group{1361}
Installation Of Cylinder Block Service Groups And Cylinder Block Hardware Kits{1201} Installation Of Cylinder Block Service Groups And Cylinder Block Hardware Kits{1201}
Installation Of 7N4013 Or 7N6342 Cylinder Block Service Group And 7N4134 Hardware Kit{1201} Installation Of 7N4013 Or 7N6342 Cylinder Block Service Group And 7N4134 Hardware Kit{1201}
Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161} Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}
Installation Of Oversize Connecting Rod Bearings{1219} Installation Of Oversize Connecting Rod Bearings{1219}
Installation Of 2N2384 And 2N2385 Solenoids{1259, 1400} Installation Of 2N2384 And 2N2385 Solenoids{1259, 1400}
Installation Of Replacement Hydraulic Pump Groups{5055} Installation Of Replacement Hydraulic Pump Groups{5055}
Using 9S9102 Thermistor Thermometer Group{0651} Using 9S9102 Thermistor Thermometer Group{0651}
Installing Sound Isolation Mounting Groups{1000, 3300} Installing Sound Isolation Mounting Groups{1000, 3300}