1997/01/27 Caterpillar

Cylinder Head Stress Plate Used During Cylinder Bore Honing And Measurement {1223}

Usage:

3114, 3116, 3126 Engines

Warranty: G

Features/Benefits

* Used to properly recondition and measure cylinder bores

* Used with 8T-0362 Bolt and 8T-3282 Washer (fourteen of each required)

* Plate must be installed on cylinder block to simulate cylinder head being assembled onto block

* When plate is installed cylinder bore is distorted as though cylinder head was installed (plate provides adequate clearance for cylinder hone and measuring tools)

* If plate is not installed during honing, bore will not be round when cylinder head is assembled onto block (this will reduce the life of the overhaul and could affect engine performance)

* Plate is hardened for added strength and durability

Specifications/Technical Information

Overall size - 789 X 215 X 50 mm (31.1 X 8.5 X 2.0 in)

Bore size (3126) - 112 mm (4.4 in)

Bore size (3114/3116) - 107 mm (4.2 in)

Bolt specifications - M20 X 2.5, 110 mm (4.3 in) long

Typical Cylinder Head Stress Plate

Caterpillar Information System:

1997/01/27 128-3102 Tap Assembly And 128-3104 Stud Puller To Remove Injector Sleeves With Oversized Lower Bore {1125}

1997/01/27 125-0200 Camshaft Pilot To Remove And Install 106-4584 Camshaft {1202}

1997/01/27 Timing Procedure Aid {1206,1162,1166}

1997/01/27 Field Repair Of Single Wire Breaks In Harnesses {1408}

1997/01/20 New Remanufactured Water Pump Groups Include Cast Iron Impellers {1361}

1997/01/20 Methods Of Obtaining Engine Flash Files {1902}

1997/01/13 Removal And Installation Procedure For The Crankshaft Wear Sleeve{7558,0701}

1997/01/13 Quickly And Accurately Set Valve Lash{1105,0766}

1997/01/13 Use 125-9622 Seal Installer To Install 118-9163 Seal In Water Pumps{1361,0708}

1997/01/13 Piston Ring Groove Gauges To Quickly And Accurately Determine Reusability Of Pistons{1214,0763}

1997/01/13 Use 126-1023 Stem Pusher For Sleeve And Coupling Removal On Hose Assemblies{5057,0684}

1997/01/13 More Collets Now Available For XT5 And XT6 Hoses Using 4C-9480 Hose Tooling Group{0684}

1997/01/27 9U-6891 Injector Tool Group To Remove And Install Injector Sleeve {1125}

1997/01/27 127-1069 Timing Pin Used To Set Piston At 100° BTDC When Testing And Adjusting Fuel Systems {1250}

1997/01/27 131-3961 Tool Group For Reclaiming Tooling From XT Hose Assemblies {5057}

1997/01/27 128-5113 Thread Repair Insert Used To Salvage Damaged Cylinder Block Stud Holes {1223,1117}

1997/01/27 130-6061 Hose Cleaner Group For Cleaning Insides Of Hydraulic Tubes, Lines And Hoses {5057,0738}

1997/02/10 Hydraulic System Pressure Relief Valve Substitution {5069,5072}

1997/03/10 Technical Information "Bargain List" {0374,0375}

1997/03/10 Identifiers Detect Contaminated Air Conditioning Refrigerant {1800,1802,7320}

1997/03/10 Proper Tensioning Of V-Belt Improves Air-Conditioning Compressor Service Life {1807,7320,1800}

1997/03/17 Special Instruction SEHS9824-01 Available For Cab Window Service Procedure; Provides New Adhesive Information For Improved Bonding Capabilities Under Cold Weather Conditions{7310}

1997/04/07 Always Use The Maintenance Interval Schedule In The Operation And Maintenance Manual When Performing Maintenance; New Look To Maintenance Section {0374,0375,1000,7000}

1997/04/14 New "Fuel System Reuse And Salvage Guides" Reference Manual Available {1250}