Axle Housing, Axle Shaft, and Wheel Flange - Disassemble
Disassembly Procedure
Start By:
- Remove the final drive planetary.
- Remove the axle housing, axle shaft, and wheel flange.
- Remove axle shaft (3) . Remove sleeve (1) . Remove retaining ring (2) from sleeve (1) .
Show/hide table
Illustration 1 | g03652782 |
- Remove axle shaft (4) .
Show/hide table
Illustration 2 | g03253758 |
- Remove bolts (7) , Washer (6) , and bushings (5) . Inspect bushings (5) , replace if necessary.
Show/hide table
Illustration 3 | g03652810 |
- Remove ring gear (8) .
Show/hide table
Illustration 4 | g03253760 |
- Remove retaining ring (9) . Use bolts (5) to remove carrier (10) from the ring gear (8) .
Show/hide table
Illustration 5 | g03253762 |
- Check the wear conditions of the components.
- Remove wheel flange (13) .
Show/hide table
Illustration 6 | g03652783 |
- Position wheel flange (13) on a flat surface and remove seal ring (11) .
Note: This is a destructive operation for seal ring (11) .
- Remove bearing cups (12) and (15) . Remove O-ring seal (14) .
- If necessary, remove seal ring (17) and bushing (16)
Show/hide table
Illustration 7 | g03653566 |
Caterpillar Information System:
2012/11/09 New Spindle is Now Used on Certain R2900G Load Haul Dump Machines {4050, 4251}
369-6017 Transmission Lifting Plate for D6R{0599, 0629, 0632, 3030} 369-6017 Transmission Lifting Plate for D6R{0599, 0629, 0632, 3030}
559C and 579C Knuckleboom Loaders Engine and Machine Warm-Up
950M, 962M, 966M, 972M, 980M, 982M, 950M Z and 962M Z Wheel Loaders General Hazard Information - Only Japanese market
450F Backhoe Loader Engine Supplement Aftercooler - Remove and Install
559C and 579C Knuckleboom Loaders Operator Station
424B and 424B HD Backhoe Loaders Power Train Axle Housing, Axle Shaft, and Wheel Flange - Install
521B and 522B Track Feller Bunchers Machine Systems Cab - Remove and Install
563C and 573C Wheel Feller Bunchers Seat Belt
C2.6 and C3.3B Engines for Caterpillar Built Machines Electric Starting Motor
424B and 424B HD Backhoe Loaders Power Train Axle Housing, Axle Shaft, and Wheel Flange - Remove
C2.6 and C3.3B Engines for Caterpillar Built Machines Alternator and Regulator
Alternator - Bosch K1/N1 General Information
Alternator - Bosch K1/N1 Service Tools
Alternator - Bosch K1/N1 Diode Assembly - Test
C1.5 and C2.2 Engines for Caterpillar Built Machines System Configuration Parameters
424B and 424B HD Backhoe Loaders Power Train Axle Housing, Axle Shaft, and Wheel Flange - Assemble
C1.5 and C2.2 Engines for Caterpillar Built Machines Replacing the ECM
2012/10/03 A New Front Track Idler Arm Is Now Available on Certain Asphalt Pavers {4151}
CD54B Vibratory Asphalt Compactor Propel System Pump Control (Electronic Displacement Control) Neutral - Test and Adjust - Split Drum
950M, 962M, 966M, 972M, 980M, 982M, 950M Z and 962M Z Wheel Loaders Operation Information
450F Backhoe Loader Engine Supplement Cooling System Package (Radiator, Aftercooler, Hydraulic Oil Cooler, Fuel Cooler) - Remove and Install
2012/10/16 Improved Latch is Now Used Certain Grenoble Built Machines {1401, 7252, 726A, 7273}
777G Off-Highway Truck TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} 777G Off-Highway Truck TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}