Gear Group (Front)
Show/hide table
Illustration 1 | g06255591 |
Typical Example (6) Crankshaft gear (11) Drive gear |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
1 | 4 | 279-0768 Bolt | Before assembly, lightly lubricate both sides of the 281-2712 Washer with clean engine oil.
Torque to |
2 | 2 | 281-2711 Washer | Before assembly, lightly lubricate both sides of the washers with clean engine oil. |
3 | 2 | 307-2402 Idler Gear As | After installation, bore of 307-2403 Bushing in the idler gear assembly is Installation depth of the bushing is |
4 | 1 | 348-7076 Front Adapter As | After installation, bore of 348-7074 Bushing in the front adapter assembly is Installation depth of the bushing is |
5 | 1 | 485-0316 Pump Adapter | After installation, bore of 318-4810 Bushing in the pump adapter is During assembly, flush the bushing with the pump adapter surface. |
7 | 1 | 348-7077 Front Adapter As | After installation, bore of 348-7074 Bushing in the front adapter assembly is Installation depth of the bushing is |
8 | 1 | 348-7075 Oil Pump Adapter | After installation, bore of 348-7074 Bushing in the oil pump adapter is Installation depth of the bushing is |
9 | 4 | 259-4598 O-Ring Seal | Before assembly, lightly lubricate the bores with the lubricant that is being sealed. |
10 | 2 | 277-6911 Idler Shaft | Diameter is |
12 | 2 | 165-4852 O-Ring Seal | Before assembly, lightly lubricate the bores with the lubricant that is being sealed. |
13 | 4 | 281-3114 Bolt | Before assembly, lightly lubricate both sides of the 281-2712 Washer with clean engine oil.
Torque to |
14 | 1 | 539-0056 Shaft As | Diameter is |
Caterpillar Information System:
797F and 797F XQ Off-Highway Truck Hydraulic Fan System Piston Motor (Hydraulic Fan) - Extra Retarding
2011/05/16 A New Gasket Is Used for the Water Lines on Certain C15 and C18 Machine Engines {1052, 1380}
563C and 573C Wheel Feller Bunchers Engine Supplement Clean Emissions Module - Remove and Install
C9.3 Engines for Caterpillar Built Machines Compression Brake - Install
C9.3 Engines for Caterpillar Built Machines Compression Brake - Assemble - Valve Assembly
C9.3 Engines for Caterpillar Built Machines Compression Brake - Disassemble - Valve Assembly
795F AC Off-Highway Truck Hydraulic and Braking System Hydraulic Tank (Brake, Hoist, Steering)
C7 Engines for Caterpillar Built Machines Inlet Manifold
C7 Engines for Caterpillar Built Machines Water Temperature Regulator
C7 Engines for Caterpillar Built Machines Cylinder Block Cover Group
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Hood - Remove and Install - Right Side Hood
541 Series 2 and 552 Series 2 Track Feller Bunchers Engine Supplement Hood - Remove and Install - Left Side Hood
AS2302C Asphalt Screed Screed Plates
AS3301C Asphalt Screed Screed Plates
2011/05/05 An Improved Hose is Available for Radiator and Oil Cooler Mounting Group {1380}
AP1000F Asphalt Paver Machine Systems Front Wheel Drive Manifold - Remove
AP1000F Asphalt Paver Machine Systems Front Wheel Drive Manifold - Install
2570C and 2670C Wheel Feller Bunchers Engine Supplement Water Pump - Remove and Install
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Engine and Transmission - Connect
2011/05/05 Updated Ring And Pinion Gear Sets For Improved Service Life {3256, 3258}
PL83 Pipelayer Mounting and Dismounting
2570C and 2670C Wheel Feller Bunchers Engine Supplement Electronic Control Module - Remove and Install
Procedure to Install the Rear Axle Oil Cooler on the 797F Off-Highway Truck {1365} Procedure to Install the Rear Axle Oil Cooler on the 797F Off-Highway Truck {1365}
PL83 Pipelayer Operator Controls