Water Temperature Regulators - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 2 |
B | 221-8647 | Seal Installer Gp | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (B) to install the lip seals.
Show/hide table
Illustration 2 g00602328 - Ensure that the lip of the seal is toward the inside of the housing.
Show/hide table
NOTICE If the water temperature regulator is installed incorrectly, it will cause the engine to overheat.
Show/hide tableIllustration 3 g06146231 - Inspect the ferrule before reassembly of water temperature regulator housing (5).
- Install lip seals (9). Install water temperature regulators (10). Install gasket (8).
Show/hide table
Illustration 4 g06146210 - Attach Tooling (A) and a suitable lifting device to water temperature regulator housing (5). The weight of water temperature regulator housing (5) is approximately
24 kg (53 lb) . - Position water temperature regulator housing (5) on the engine and install bolts (6).
- Install elbow (4) and bolts (3), if necessary.
- Connect tube assembly (1) to elbow (4).
- Install clamp assembly (2) and bolts (7).
- Fill the cooling system with coolant to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Show/hide table
Illustration 1 | g00911612 |
Caterpillar Information System:
966H Wheel Loader and 972H Wheel Loader Power Train MID 081 - CID 0621 - FMI 03
2008/02/25 New Software For the Machine ECM Is Now Available {7620}
511 Track Feller Buncher, 521 Track Feller Buncher, 522 Track Feller Buncher and 532 Track Feller Buncher Machine Systems Piston Pump (Main Hydraulic)
3512C Engine for Caterpillar Built Machines Water Temperature Regulators - Remove
Replacement of the Cab Roof on Certain Caterpillar Machines {7301} Replacement of the Cab Roof on Certain Caterpillar Machines {7301}
C4.4 Engines For Caterpillar Built Machines Start Relay Circuit - Test
24M Motor Grader Machine Systems Fuel Tank - Install
24M Motor Grader Machine Systems Fuel Tank - Remove
C175-16 and C175-20 Engines for Off-Highway Trucks Camshaft
MINEGEM Machine Control ; Guidance Products Display Description
2008/05/05 Improved Service Brake and Service Brake Lines Group Reduces Seal Leaks {4251, 4257}
277C, 277C2, 287C, 287C2 and 297C Multi Terrain Loaders Machine Systems Gear Motor (Fan, Aftercooler)
3512C Engine for Caterpillar Built Machines Water Pump - Remove
C13, C15, and C18 Generator Set Engines Camshaft
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Crankcase Breather
3512C Engine for Caterpillar Built Machines Water Pump - Install
2008/06/23 Changes to Operation and Maintenance , "Track (Rubber) - Inspect/Adjust" {4197, 4198}
A False Diagnostic Code is Generated When Flashing Software in Some Excavators{1901, 1902, 7600, 7610, 7620} A False Diagnostic Code is Generated When Flashing Software in Some Excavators{1901, 1902, 7600, 7610, 7620}
120K Motor Grader Safety Messages
2008/03/03 Caterpillar Machine Control and Guidance Repair Center {7220, 7604}
120K Motor Grader Additional Messages
3512C Engine for Caterpillar Built Machines Auxiliary Water Pump - Remove
2008/03/17 The Procedure to Mount the Rear Axle is Updated {3260, 3278, 3282, 4068}
2008/04/28 An Improved Refrigerant Compressor Gp Is Available {1802}