Water Temperature Regulators - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7573 | Link Bracket | 2 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Drain the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change". Drain the cooling system until the level of the coolant is below the exhaust manifolds.
Show/hide table
Illustration 1 g06146210 - Remove bolts (7) and clamp assembly (2).
- Disconnect tube assembly (1) from elbow (4).
- Remove bolts (3) and elbow (4), if necessary.
- Attach Tooling (A) and a suitable lifting device to water temperature regulator housing (5). The weight of water temperature regulator housing (5) is approximately
24 kg (53 lb) . - Remove bolts (6) and water temperature regulator housing (5).
Show/hide table
Illustration 2 g06146231 - Remove gasket (8). Remove water temperature regulators (10) from water temperature regulator housing (5). If necessary, remove lip seals (9).
Visually inspect the ferrule and lip seals (9) for water temperature regulators (10). Obtain new parts for assembly, if necessary.
Caterpillar Information System:
Replacement of the Cab Roof on Certain Caterpillar Machines {7301} Replacement of the Cab Roof on Certain Caterpillar Machines {7301}
C4.4 Engines For Caterpillar Built Machines Start Relay Circuit - Test
24M Motor Grader Machine Systems Fuel Tank - Install
24M Motor Grader Machine Systems Fuel Tank - Remove
C175-16 and C175-20 Engines for Off-Highway Trucks Camshaft
MINEGEM Machine Control ; Guidance Products Display Description
2008/05/05 Improved Service Brake and Service Brake Lines Group Reduces Seal Leaks {4251, 4257}
277C, 277C2, 287C, 287C2 and 297C Multi Terrain Loaders Machine Systems Gear Motor (Fan, Aftercooler)
2008/03/03 An Improved Electrical Circuit for the Level Alarm on the Hydraulic Tank is Now Used on Asphalt Pavers {1408, 5056, 7422}
24M Motor Grader Power Train Torque Converter - Install
24M Motor Grader Power Train Torque Converter - Remove
C4.4 Industrial Engine Engine Rating Conditions
511 Track Feller Buncher, 521 Track Feller Buncher, 522 Track Feller Buncher and 532 Track Feller Buncher Machine Systems Piston Pump (Main Hydraulic)
2008/02/25 New Software For the Machine ECM Is Now Available {7620}
966H Wheel Loader and 972H Wheel Loader Power Train MID 081 - CID 0621 - FMI 03
3512C Engine for Caterpillar Built Machines Water Temperature Regulators - Install
3512C Engine for Caterpillar Built Machines Water Pump - Remove
C13, C15, and C18 Generator Set Engines Camshaft
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Crankcase Breather
3512C Engine for Caterpillar Built Machines Water Pump - Install
2008/06/23 Changes to Operation and Maintenance , "Track (Rubber) - Inspect/Adjust" {4197, 4198}
A False Diagnostic Code is Generated When Flashing Software in Some Excavators{1901, 1902, 7600, 7610, 7620} A False Diagnostic Code is Generated When Flashing Software in Some Excavators{1901, 1902, 7600, 7610, 7620}
120K Motor Grader Safety Messages
2008/03/03 Caterpillar Machine Control and Guidance Repair Center {7220, 7604}