Torque Converter - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 311-1362     | 真空盖     | 1     |
B     | 1U-9200     | 杠杆式提升起重机     | 2     |
C     | 138-7575     | 连杆支架     | 2     |
开始:
- 拆下发动机护罩。 请参阅拆解和装配, "发动机护罩(防护罩)- 拆卸"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
在发动机和油泵停转后,本机器的液压系统中可能仍保持着液压油压力。 如果在对液压进行任何维护前没有释放此压力,可能会造成严重的人身伤害。 为了避免可能的人身伤害,在进行接头、软管或液压零部件操作之前应释放液压系统压力。 开始维护之前把所有机具降到地面。 如果必须在机具升起位置时维护、测试或调整液压系统,则需要适当支撑住机具和提升油缸。 一定要将机器移到远离其它机器行走线路的地方。 发动机运转并进行测试或调整时,应保证其他人员远离机器。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查 O 形密封圈。 更换过度磨损或损坏的 O 型密封圈。
- 释放系统压力。 请参阅操作和保养手册, "系统压力 - 释放"。
- 将工具 (A) 安装到液压箱上。 将一条供气软管连接到工具 (A) 上。 施加 276 到 414 kPa (40 到 60 psi) 的气压。 此步骤将使液压系统抽吸出真空。
Show/hide table
图 1 | g01439073 |
- 断开软管组件 (1) 。 拆下螺栓 (2) 。
Show/hide table
图 2 | g01488834 |
- 拆下夹子 (3) 。 拆下夹子 (4) 。
Show/hide table
图 3 | g01488334 |
- 断开线束组件 (5) 。 断开软管组件 (6) 。 拆下螺栓 (7) 。
Show/hide table
图 4 | g01488373 |
- 断开线束组件 (8) 并拆下接线紧固件。 拆卸管组件 (9) 。 拆下螺栓 (10) 。 拆下安全阀 (11) 。
Show/hide table
图 5 | g01497353 |
Show/hide table
图 6 | g01496893 |
- 拆下 O 型密封圈 (12) 。
Show/hide table
图 7 | g01501771 |
- 拆下夹子 (13) 。
Show/hide table
图 8 | g01496393 |
- 卸下支架组件 (14) 。
Show/hide table
图 9 | g01488653 |
- 将适当起吊设备连在泵组件 (15) 上。 泵组件 (15) 的重量大约为 73 kg (160 lb)。 拆下螺栓 (16) 。
Show/hide table
图 10 | g01488395 |
- 利用工具 (B) 将泵组件 (15) 固定到旁边。
Show/hide table
图 11 | g01488613 |
- 取下 O 形密封圈 (17) 。
- 断开软管 (18) 。 拆下接头 (19) 。
Show/hide table
图 12 | g01489053 |
- 断开管子组件 (20) 。 断开软管组件 (21) 、 (22) 和 (23) 。
Show/hide table
图 13 | g01489073 |
- 使用工具 (B) 和适当的起吊设备支撑万向节 (10) 。 拆下螺栓 (25) 。 将万向节 (24) 安置到旁边。
Show/hide table
图 14 | g01489154 |
Show/hide table
图 15 | g01489173 |
- 断开线束组件 (26) 和线束组件 (28) 。 拆下螺栓 (27) 。 拆下调节阀 (28) 。
Show/hide table
图 16 | g01489893 |
- 拆下 O 型密封圈 (29) 。
Show/hide table
图 17 | g01489914 |
- 卸下支架 (30) 。
Show/hide table
图 18 | g01489933 |
- 将工具 (C) 和适当的起吊设备安装到变矩器 (31) 上。 变矩器 (31) 的重量大约为 295 kg (650 lb)。
Show/hide table
图 19 | g01489213 |
- 拆下螺栓 (32) 。 利用两条螺栓 (32) 将变矩器 (31) 与飞轮壳分开。 利用工具 (B) 、工具 (C) 和适当的起吊设备拆下变矩器 (31) 。
Caterpillar Information System:
C4.4 Industrial Engine Engine Rating Conditions
C4.4 Industrial Engine Engine Rating Definitions
R2900G Load Haul Dump Secondary Steering - If Equipped
R2900G Load Haul Dump Indicators
MINEGEM Machine Control ; Guidance Products General Information
2008/04/21 The Engine Oil Filler and Oil Level Gauge Groups are Improved {1316, 1326, 7513}
3512C Engine for Caterpillar Built Machines Air Inlet Manifold - Remove and Install
793F AC Off-Highway Truck Hydraulic Fan and Steering System Piston Pump (Hydraulic Fan and Steering)
797B Off-Highway Truck Electrical System
793F and 793F XQ Off-Highway Truck Fast Fill Service System General Information
12M, 140M and 160M Motor Graders Hydraulic and Steering System Steering System - Purge
120K Motor Grader Stopping the Engine if an Electrical Malfunction Occurs
24M Motor Grader Power Train Torque Converter - Install
2008/03/03 An Improved Electrical Circuit for the Level Alarm on the Hydraulic Tank is Now Used on Asphalt Pavers {1408, 5056, 7422}
277C, 277C2, 287C, 287C2 and 297C Multi Terrain Loaders Machine Systems Gear Motor (Fan, Aftercooler)
2008/05/05 Improved Service Brake and Service Brake Lines Group Reduces Seal Leaks {4251, 4257}
MINEGEM Machine Control ; Guidance Products Display Description
C175-16 and C175-20 Engines for Off-Highway Trucks Camshaft
24M Motor Grader Machine Systems Fuel Tank - Remove
24M Motor Grader Machine Systems Fuel Tank - Install
C4.4 Engines For Caterpillar Built Machines Start Relay Circuit - Test
Replacement of the Cab Roof on Certain Caterpillar Machines {7301} Replacement of the Cab Roof on Certain Caterpillar Machines {7301}
3512C Engine for Caterpillar Built Machines Water Temperature Regulators - Remove
511 Track Feller Buncher, 521 Track Feller Buncher, 522 Track Feller Buncher and 532 Track Feller Buncher Machine Systems Piston Pump (Main Hydraulic)