Swivel - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 311-1362     | 真空舱     | 1     |
B     | 138-7575     | 连杆支架     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 释放系统压力。 请参阅操作和保养手册, "系统压力 - 释放"。
- 将工具 (A) 安装到液压油箱上。 将一条供气软管连接到工具 (A) 上。 施加 138 kPa (20 psi) 的压力。 此步骤将使液压系统抽吸出真空。
Show/hide table
图 1 | g01368952 |
- 断开软管组件 (1) 和软管组件 (2) 。
Show/hide table
图 2 | g01342880 |
- 拆下螺栓 (3) 。 断开软管组件 (4) 。
Show/hide table
图 3 | g01342884 |
- 卸下开口销 (5) 。 拆下销 (6) 。 降下支架 (7) 。
Show/hide table
图 4 | g01342888 |
- 将工具 (B) 和适当的起吊设备连接到旋转台座 (8) 上。 旋转台座 (8) 的重量约为 39 kg (85 lb)。
Show/hide table
图 5 | g01342891 |
- 拆下螺栓 (9) 。 卸下旋转台座 (8) 。
Caterpillar Information System:
Filtration Procedure for Load, Haul, Dump Hydraulic Oil {0680, 0768, 5050, 5056, 5068} Filtration Procedure for Load, Haul, Dump Hydraulic Oil {0680, 0768, 5050, 5056, 5068}
PL1000E Communication ECM Hardware Configuration
770 and 772 Off-Highway Truck Power Train Governor Pedal
287C2 Compact Track Loader and 287C, 277C, 277C2 and 297C Multi Terrain Loaders Machine Systems Gear Pump (Charge) - Install - High Flow
287C2 Compact Track Loader and 287C, 277C, 277C2 and 297C Multi Terrain Loaders Machine Systems Gear Pump (Charge) - Remove - High Flow
14L Motor Grader All Wheel Drive Electronic Control System Electronic Control Module (ECM) - Replace
14L Motor Grader All Wheel Drive Electronic Control System Electronic Control Module (ECM) - Configure
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System Electronic Control Module (ECM) - Flash Program
14L Motor Grader All Wheel Drive Electronic Control System Wiring Harness (Short Circuit) - Test
14L Motor Grader All Wheel Drive Electronic Control System Wiring Harness (Open Circuit) - Test
Product Link PL121SR{7606} Product Link PL121SR{7606}
C4.2 and C6.4 Engines for Caterpillar Built Machines Welding Precaution
16M Motor Grader Machine Systems Swivel - Install
Procedure to Install Improved Software and Cable Assemblies on the Cold Planers{0779, 7620} Procedure to Install Improved Software and Cable Assemblies on the Cold Planers{0779, 7620}
14M Motor Grader Machine Systems Ripper - Remove
14M Motor Grader Machine Systems Ripper - Install
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C Multi Terrain Loaders Power Train Piston Motor (Hydrostatic) - Disassemble
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C Multi Terrain Loaders Power Train Piston Motor (Hydrostatic) - Assemble
2007/01/22 Use the Correct Parts in the Valve Train {1100}
2007/01/22 Use the Correct Parts in the Valve Train {1100}
773D Off-Highway Truck Power Train Electronic Control (Transmission Gear Indicator)
770 and 772 Off-Highway Truck Suspension Cylinder Rear Suspension (Cylinder)
770 and 772 Off-Highway Truck Suspension Cylinder Front Suspension (Cylinder)
770 and 772 Off-Highway Truck Suspension Cylinder Pressure Sensor (Payload Monitor) - If Equipped