Ripper - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1U-9202     | 操纵杆滚轮起重机     | 1     |
B     | 180-3032     | 修理台架     | 2     |
C     | 1U-7505     | 液压千斤顶     | 1     |
D     | 1P-1834     | 轴承拆卸工具适配器     | 1     |
4C-9633 | 拉拔器螺柱     | 1     | |
6V-3160 | 双作用油缸     | 1     | |
3S-6224 | 电动液压泵总成     | 1     | |
9U-6833 | 全高螺母     | 1     | |
5F-7693 | 隔套组件     | 1     | |
E     | 1P-1835     | 轴承拆卸工具适配器     | 1     |
4C-9633 | 拉拔器螺柱     | 1     | |
6V-3160 | 双作用油缸     | 1     | |
3S-6224 | 电动液压泵总成     | 1     | |
9U-6833 | 全高螺母     | 1     | |
5F-7693 | 隔套组件     | 1     |
开始:
- 卸下裂土器提升油缸。 请参阅拆解和组装, "裂土器提升油缸 - 拆卸和安装"。
- 拆下底部防护罩。 请参阅拆解和组装, "底部防护罩 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 将适当的起吊设备连接至裂土器 (1) 上。 裂土器 (1) 的重量约为 1134 kg (2500 lb)。 提升裂土器 (1) 。 在裂土器 (1) 下安装适当的挡块。 将裂土器 (1) 降低至挡块上。
Show/hide table
图 1 | g00933791 |
- 卸下螺栓 (2) 。
Show/hide table
图 2 | g00933795 |
- 将适当的起吊设备连接在连杆组件 (3) 上。 连杆组件的重量约为 30 kg (65 lb)。 卸下销 (4) ,然后卸下连杆组件 (3) 。 在对面重新执行此步骤。
- 将工具 (A) 和适当的起吊设备连接至裂土器 (1) 。 提升裂土器 (1) ,然后安装工具 (B) 。
Show/hide table
图 3 | g00933797 |
Show/hide table
图 4 | g00933802 |
- 拆下螺栓 (5) 和销 (6) 。 在对面重新执行此步骤。 卸下裂土器 (1) 。
- 将适当的起吊设备连接至连杆组件 (7) 上。 连杆组件 (7) 的重量约为 329 kg (725 lb)。
Show/hide table
图 5 | g00933803 |
- 卸下螺栓 (8) ,然后卸下销 (9) 。 在对面重新执行此步骤。 卸下连杆组件 (7) 。 卸下软管组件 (10) 。
- 将适当的起吊设备连接至连杆组件 (11) 。 连杆组件 (11) 的重量约为 102 kg (225 lb)。
Show/hide table
图 6 | g01343113 |
- 使用撬棒将连杆组件 (11) 移至边侧,然后将其放低到适当的挡块上。 在对面重新执行此步骤。
- 将适当的起吊设备连接至板组件 (12) 上。 板组件 (12) 的重量约为 148 kg (325 lb)。 拆下螺栓 (13) 。 在对面重新执行此步骤。
Show/hide table
图 7 | g01343120 |
Show/hide table
图 8 | g01343126 |
- 拆下螺栓 (14) 。 在对面重新执行此步骤。 卸下板组件 (12) 。
- 将适当的起吊设备连接至连杆组件 (11) 。 连杆组件 (11) 的重量约为 102 kg (225 lb)。 使用张力支撑连杆组件 (11) 。
Show/hide table
图 9 | g01343132 |
- 拆下螺栓 (15) 。
- 将销 (16) 转向串联壳体 (17) (未显示),然后卸下连杆组件 (11) 。.
- 将密封件 (18) 从连杆组件 (7) 上卸下。
Show/hide table
图 10 | g01343133 |
- 使用工具 (D) 将轴承 (19) 从连杆组件 (7) 上卸下。 对其余轴承重复此步骤。
- 将密封件 (20) 从连杆组件 (3) 上卸下。 对连杆的另一端重复此步骤。 对其余连杆重复此步骤。
Show/hide table
图 11 | g01343134 |
- 使用工具 (E) 卸下轴承 (21) 。 对连杆的另一端重复此步骤。 对其余连杆重复此步骤。
Caterpillar Information System:
Procedure to Install Improved Software and Cable Assemblies on the Cold Planers{0779, 7620} Procedure to Install Improved Software and Cable Assemblies on the Cold Planers{0779, 7620}
16M Motor Grader Machine Systems Swivel - Install
16M Motor Grader Machine Systems Swivel - Remove
Filtration Procedure for Load, Haul, Dump Hydraulic Oil {0680, 0768, 5050, 5056, 5068} Filtration Procedure for Load, Haul, Dump Hydraulic Oil {0680, 0768, 5050, 5056, 5068}
PL1000E Communication ECM Hardware Configuration
770 and 772 Off-Highway Truck Power Train Governor Pedal
287C2 Compact Track Loader and 287C, 277C, 277C2 and 297C Multi Terrain Loaders Machine Systems Gear Pump (Charge) - Install - High Flow
287C2 Compact Track Loader and 287C, 277C, 277C2 and 297C Multi Terrain Loaders Machine Systems Gear Pump (Charge) - Remove - High Flow
14L Motor Grader All Wheel Drive Electronic Control System Electronic Control Module (ECM) - Replace
14L Motor Grader All Wheel Drive Electronic Control System Electronic Control Module (ECM) - Configure
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System Electronic Control Module (ECM) - Flash Program
14L Motor Grader All Wheel Drive Electronic Control System Wiring Harness (Short Circuit) - Test
14M Motor Grader Machine Systems Ripper - Install
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C Multi Terrain Loaders Power Train Piston Motor (Hydrostatic) - Disassemble
279C2 Compact Track Loader and 287C, 277C, 277C2 and 297C Multi Terrain Loaders Power Train Piston Motor (Hydrostatic) - Assemble
2007/01/22 Use the Correct Parts in the Valve Train {1100}
2007/01/22 Use the Correct Parts in the Valve Train {1100}
773D Off-Highway Truck Power Train Electronic Control (Transmission Gear Indicator)
770 and 772 Off-Highway Truck Suspension Cylinder Rear Suspension (Cylinder)
770 and 772 Off-Highway Truck Suspension Cylinder Front Suspension (Cylinder)
770 and 772 Off-Highway Truck Suspension Cylinder Pressure Sensor (Payload Monitor) - If Equipped
3508 EUI Engine for Off-Highway Truck/Tractors Cylinder Block
IT38H Integrated Toolcarrier and 938H Wheel Loader Machine Systems Cab - Remove
14L Motor Grader Transmission Oil Filter Base - Disassemble