Rotor Drive Differential - Install
Installation Procedure
- Attach a suitable lifting device to the rotor drive differential (13) . The weight of the rotor drive differential is approximately 204 kg (450 lb). Place rotor drive differential (13) on a stand.
Show/hide table
Illustration 1 | g01296024 |
- Attach a suitable lifting device to the chain case hub. Install washer (15) and chain case hub (13) to rotor drive differential (13) .
Show/hide table
Illustration 2 | g01293444 |
- Cut a 45 degree bevel angle on rubber plug (12) .
Show/hide table
Illustration 3 | g02239094 |
- Install rubber plug (12) , washer (11) , and nut (10) . Torque nut (10) to 136 N·m (100 lb ft), then back nut (10) off half of a flat.
Show/hide table
Illustration 4 | g01293447 |
- Cut a 45 degree bevel angle on rubber plug (9) .
Show/hide table
Illustration 5 | g02239155 |
- Install one shim (8) , rubber plug (9) , and lockwasher (7) . Bend a minimum of two tabs on lockwasher (7) onto inner nut (10) .
Show/hide table
Illustration 6 | g01293462 |
Note: No more than two shims can be installed on either side of lockwasher (7)
- Install two shims (6) and nut (5) . Torque nut (5) to 136 N·m (100 lb ft).
Note: The shimming procedure will be completed during the installation of the rotor drive axle assemblies.
Show/hide table
Illustration 7 | g01293464 |
Show/hide table
Illustration 8 | g01293466 |
- Install chain drive case (4) and bolts (3) .
Show/hide table
Illustration 9 | g01293468 |
- Install the other chain drive case.
- Attach a suitable lifting device to spacer tube (1) . The weight of the spacer tube is approximately 181 kg (400 lb). Install spacer tube (1) and bolts (2) .
Show/hide table
Illustration 10 | g01293470 |
End By:
- Install the mixing chamber. Refer to Disassembly and Assembly, "Mixing Chamber - Install".
- Install the rotor stub shaft gp. Refer to Disassembly and Assembly, "Rotor Stub Shaft Gp - Install".
- Install the rotor drive axle assembly. Refer to Disassembly and Assembly, "Rotor Drive Axle Shaft - Install".
Caterpillar Information System:
C175-16 Locomotive Engine Valve Lash - Adjust
RM-300 Reclaimer Mixer Machine Systems Rotor Drive Differential - Remove
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Braking System Brake Accumulator
AccuGrade® GPS System Components
450E Backhoe Loader Transmission Oil Filter - Replace
450E Backhoe Loader Transmission Oil - Change
450E Backhoe Loader Hydraulic System Oil Filter - Replace
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Power Train Electronic Control System MID 027 - CID 2176 - FMI 06
RM-300 Reclaimer Mixer Machine Systems Rotor Transmission - Assemble
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Power Train Electronic Control System MID 027 - CID 2176 - FMI 05
RM-300 Reclaimer Mixer Machine Systems Rotor Transmission - Disassemble
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Power Train Electronic Control System MID 027 - CID 2176 - FMI 03
450E Backhoe Loader Transmission Oil Level - Check
2006/11/27 An Improved Elbow and a Tube for the Coolant Lines Is Used {1380}
450E Backhoe Loader Transmission Oil Sample - Obtain
2006/07/31 Bearing Inserts Are Now Used in Frame Steering Bracket {7051, 7073}
450E Backhoe Loader Transmission Magnetic Screen - Clean
The Hoses that connect to the Brake Reservoir are Too Long{4269} The Hoses that connect to the Brake Reservoir are Too Long{4269}
572R Series II Pipelayer Hydraulic System Hydraulic Tank and Filter
D6K Track-Type Tractor Electrohydraulic Power Train Track Roller
793D Off-Highway Truck/Tractor Control Valve (Hoist) - Remove
793D Off-Highway Truck/Tractor Control Valve (Hoist) - Install
450E Backhoe Loader Operator Controls
246C, 256C, 262C and 272C Skid Steer Loaders Fire Extinguisher Location