Hydraulic Cylinder (Front Steering) - Remove and Install
拆卸步骤
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
Show/hide table
配备锁止阀的油缸即使在软管拆卸后也会长时间保持高压状态。 如果拆卸锁止阀或解体油缸之前没有释放所有压力,则可能会导致人身伤亡。 拆卸锁止阀或解体油缸之前确保释放所有压力。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修机器时,务必小心,确保用容器盛接流出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关可提供予卡特彼勒机器的工具及适合于盛装油液的容器,请参阅专门出版物, NENG2500, "卡特彼勒工具及车间用品指南"。 根据当地法规处置所有液体。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 将适当的起吊设备放置在底部护板 (1) 的下方。 拆下螺栓 (2) ,然后拆下底部护板 (1) 。 底部护板 (1) 的重量约为 27 kg (60 lb)。
Show/hide table
图 1 | g01272586 |
- 将软管组件 (8) 从液压油缸 (7) 上断开。
Show/hide table
图 2 | g01272588 |
- 将螺栓 (4) 和销组件 (3) 从液压油缸 (7) 上拆下。
- 将螺栓 (5) 、销组件 (6) 和液压油缸 (7) 从机器上拆下。
安装步骤
- 安装液压油缸 (7) 、销组件 (6) 和螺栓 (5) 。
Show/hide table
图 3 | g01272588 |
- 将销组件 (3) 和螺栓 (4) 安装到液压油缸 (7) 。
- 将软管组件 (8) 连接到液压油缸 (7) 。
- 将适当的起吊设备放置在底部护板 (1) 的下方。 安装底部护板 (1) 和螺栓 (2) 。 底部护板 (1) 的重量约为 27 kg (60 lb)。
Show/hide table
图 4 | g01272586 |
Caterpillar Information System:
770 and 772 Off-Highway Truck Hydraulic and Braking System Control Valve (Hoist)
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Chassis Electronic Control System MID 087 - CID 0177 - FMI 08
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2209 - FMI 08
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2209 - FMI 04
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2209 - FMI 03
3508 EUI Engine for Off-Highway Truck/Tractors Engine Oil Pan
EquipmentManager User Guide Manage Equipment Groups
3508 EUI Engine for Off-Highway Truck/Tractors Engine Oil Filter Base
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2208 - FMI 08
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2208 - FMI 04
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2208 - FMI 03
C9 Engine for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
Filtration Procedure for Wheeled Excavator Hydraulic Oil {0680, 0768, 5050, 5056} Filtration Procedure for Wheeled Excavator Hydraulic Oil {0680, 0768, 5050, 5056}
2006/09/04 Correction to Operation and Maintenance Manual , "Capacities (Refill)" {7000, 7560}
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Rotor Drive Differential - Remove
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Rotor Drive Differential - Install
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Rotor Drive Planetary - Install
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Rotor Drive Planetary - Remove
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0269 - FMI 03
773G and 775G Quarry Trucks Chassis Electronic Control System MID 087 - CID 0269 - FMI 04
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems General Information (Auxiliary Hydraulic System)
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Operator Controls (Auxiliary Hydraulic System)
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Electrical System (Auxiliary Hydraulic)
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Position Sensor (Rotor Depth, Front Steering, and Rear Steering)