Engine Oil Filter Base
Show/hide table
Illustration 1 | g01272386 |
(1) Clamp bolt
Use the following bolt tightening sequence in order to tighten the clamp bolts.
- Place the clamp assembly so that the clamp assembly is snug against the tube.
- Tighten the clamp assembly to the adapter.
Torque ... 47 ± 9 N·m (35 ± 7 lb ft)
- Tighten the clamp assembly to the tube.
Torque ... 47 ± 9 N·m (35 ± 7 lb ft)
(2) Stud
-
Apply 154-9731 Thread Lock Compound to the last 10.2 ± 1.5 mm (.40 ± .06 inch) of the thread at the base end of the stud.
- Torque ... 80 ± 14 N·m (60 ± 10 lb ft)
(3) Oil filter
- Put clean engine oil on the oil filter seal.
- Put oil filter (3) in position and tighten the oil filter until the seal contacts the oil filter base.
- Tighten the filter for an additional 360 degrees.
(4) Oil filter bypass valve
- The oil filter bypass valves must open at the following pressure difference: ... 230 ± 20 kPa (33 ± 3 psi)
(5) 7G-6713 Spring for the oil filter bypass valves
- Length under test force ... 57.2 mm (2.25 inch)
- Test force ... 109 ± 5 N (24.5 ± 1.1 lb)
- Free length after test ... 99.7 mm (3.93 inch)
- Outside diameter ... 21.23 mm (0.836 inch)
- Color code (stripes) ... one light blue stripe
- Test force ... 109 ± 5 N (24.5 ± 1.1 lb)
Caterpillar Information System:
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2208 - FMI 08
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2208 - FMI 04
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2208 - FMI 03
C9 Engine for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
2006/05/29 New Software Prevents a False Warning for the Hydraulic Oil Temperature and a False Message During the Calibration of the Fan Speed {1408, 7610, 7620}
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2207 - FMI 08
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2207 - FMI 04
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2207 - FMI 03
770 and 772 Off-Highway Truck Engine Air Precleaner - Clean
770 and 772 Off-Highway Truck Differential and Final Drive Oil Level - Check
C9 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold - Remove
EquipmentManager User Guide Manage Equipment Groups
3508 EUI Engine for Off-Highway Truck/Tractors Engine Oil Pan
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2209 - FMI 03
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2209 - FMI 04
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2209 - FMI 08
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Chassis Electronic Control System MID 087 - CID 0177 - FMI 08
770 and 772 Off-Highway Truck Hydraulic and Braking System Control Valve (Hoist)
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Hydraulic Cylinder (Front Steering) - Remove and Install
Filtration Procedure for Wheeled Excavator Hydraulic Oil {0680, 0768, 5050, 5056} Filtration Procedure for Wheeled Excavator Hydraulic Oil {0680, 0768, 5050, 5056}
2006/09/04 Correction to Operation and Maintenance Manual , "Capacities (Refill)" {7000, 7560}
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Rotor Drive Differential - Remove
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Rotor Drive Differential - Install