Flywheel Housing - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7575 | 连杆支架 | 2 |
B | - | 导向螺栓 M12 x 1.75 x 5 in |
2 |
开始:
- 拆下飞轮。 参考拆解和组装, "飞轮 - 拆卸和安装"。
- 拆下电起动马达。 请参阅拆解和组装, "电起动马达 - 拆卸和安装"。
- 拆下两个螺栓 (3)。 将工具 (B) 安装到缸体中。
- 将工具 (A) 和适当的起吊设备连接到飞轮壳 (1) 上。 飞轮壳 (1) 的重量约为
37 kg (82 lb) 。 - 拆下螺栓 (2)。 拆下剩余的螺栓 (3)。
- 拆下将发动机油底壳固定在飞轮壳 (1) 上的螺栓 (4) (图上未显示)。 拆下飞轮壳 (1)。
Show/hide table
图 1 | g01272224 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7575 | 连杆支架 | 2 |
B | - | 导向螺栓 M12 x 1.75 x 5 in |
2 |
C | 1U-8846 | 密封垫密封胶 | 1 |
- 安装之前先在飞轮壳整个安装面上涂敷工具 (C)。
Show/hide table
图 2 g01272224 - 将工具 (B) 安装到缸体中。
- 将工具 (A) 和适当的起吊设备连接到飞轮壳 (1) 上。 飞轮壳 (1) 的重量约为
37 kg (82 lb) 。 将飞轮壳 (1) 放置到工具 (B) 上。 - 安装螺栓 (2)。 安装螺栓 (3)。 拆下工具 (B),然后安装其余的螺栓 (3)。
- 安装将发动机油底壳固定在飞轮壳 (1) 上的螺栓 (4)(图上未显示)。
结束:
- 安装电起动马达。 请参阅拆解和组装, "电起动马达 - 拆卸和安装"。
- 安装飞轮。 参考拆解和组装, "飞轮 - 拆卸和安装"。
Caterpillar Information System:
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold - Remove
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold - Install
2006/05/29 An Improved Hub for the Differential Lock Is Available {3256, 3258}
R1700G Load Haul Dump Fuel Shutoff Valve
R1700G Load Haul Dump Fuses - Replace
AccuGrade® GPS (CD700) Design Surface Type
AccuGrade® GPS (CD700) Display Navigation
AccuGrade® GPS (CD700) Text View
AccuGrade® GPS (CD700) Profile View
AccuGrade® GPS (CD700) Cross Section View
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2206 - FMI 08
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2206 - FMI 04
770 and 772 Off-Highway Truck Differential and Final Drive Oil Level - Check
770 and 772 Off-Highway Truck Engine Air Precleaner - Clean
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2207 - FMI 03
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2207 - FMI 04
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2207 - FMI 08
2006/05/29 New Software Prevents a False Warning for the Hydraulic Oil Temperature and a False Message During the Calibration of the Fan Speed {1408, 7610, 7620}
C9 Engine for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2208 - FMI 03
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2208 - FMI 04
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2208 - FMI 08
3508 EUI Engine for Off-Highway Truck/Tractors Engine Oil Filter Base
EquipmentManager User Guide Manage Equipment Groups