Transmission (Power Shift) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 180-3034     | 一套修理台     | 4     |
B     | 8S-7615     | 触针     | 2     |
4C-6486 | 台架     | 2     | |
8S-7641 | 管     | 2     | |
8S-8048 | 鞍座     | 2     | |
C     | 208-5040     | 支持管     | 1     |
D     | 1U-7505     | 液压千斤顶     | 1     |
- 将工具 (D) 连接到变速箱组件 (31) 。 变速箱组件 (31) 的重量约为 255 kg (562 lb)。
Show/hide table
图 1 | g01244138 |
Show/hide table
图 2 | g01243675 |
- 使用工具 (D) 安装变速箱组件 (31) 。
- 将电缆带 (37) 从变矩器的驱动板 (38) 上拆下。
Show/hide table
图 3 | g01243966 |
- 安装螺栓 (34) 。
Show/hide table
图 4 | g01249112 |
- 将安装件 (40) 和 (43) 安装到变速箱组件 (31) 的两侧上。 安装安装螺栓 (39) 和 (44) 。 安装螺栓 (42) 和 (46) ,然后安装螺母 (41) 和 (45) 。
Show/hide table
图 5 | g01243880 |
Show/hide table
图 6 | g01243894 |
- 旋转飞轮 (35) 以安装螺栓 (36) 。
Show/hide table
图 7 | g01243827 |
- 安装盖 (33) 和螺栓 (32) 。
Show/hide table
图 8 | g01249114 |
- 安装变速箱机油滤清器。 请参考 操作和保养手册, "变速箱机油滤清器 - 更换"。
- 将软管 (30) 安装到液压油箱,然后安装卡箍 (29) 。 连接软管组件 (28) 。
Show/hide table
图 9 | g01243674 |
- 将变速箱加注管 (25) 移入活塞,然后安装卡子 (27) 。
Show/hide table
图 10 | g01243666 |
- 安装固定变速箱加注管 (25) 的螺栓 (26) 。
Show/hide table
图 11 | g01243665 |
- 将滤清器组件 (22) 移动到相应的位置并安装螺栓 (21) 。 将歧管组件 (23) 移动就位后安装螺栓 (24) 。
Show/hide table
图 12 | g01243819 |
- 连接软管组件 (17) 、 (18) 、 (19) 和 (20) 。
注: 软管组件 (19) 和 (20) 与变速箱一起安装。
Show/hide table
图 13 | g01243661 |
- 将软管组件 (16) 连接至变速箱的右侧。
Show/hide table
图 14 | g01243838 |
- 安装电磁阀 (11) 和 (15) ,然后安装柱塞。 安装螺母 (12) 和 (14) 。 连接线束组件 (13) 。
Show/hide table
图 15 | g01243656 |
- 连接线束组件 (8) 、 (9) 和 (10) 。
Show/hide table
图 16 | g01243338 |
- 连接线束组件 (1) 、 (2) 、 (3) 、 (4) 、 (5) 、 (6) 和 (7) 。
Show/hide table
图 17 | g01243334 |
- 使用工具 (D) 拆下工具 (A) 、工具 (B) 和工具 (C) 。 将机器降至地面上。
Show/hide table
图 18 | g01244146 |
Show/hide table
图 19 | g01244175 |
Show/hide table
图 20 | g01244145 |
- 安装前驱动轴。 请参考拆解和组装, "驱动轴(前)- 拆卸和安装"。
- 安装活塞泵。 请参阅拆解和组装, "活塞泵 - 安装"。
- 变速箱里注油。 请参考操作和保养手册, "变速箱油 - 更换"。
Caterpillar Information System:
24M Motor Grader Braking and Hydraulic Fan System Piston Pump (Brake, Hydraulic Fan) Margin Pressure - Test and Adjust
C15 and C18 Generator Set Engines Engine - Install
C9.3 Engine for Caterpillar Built Machines Cylinder Head
Convert the Buckets from the J-Series Base Edge Assemblies to the K-Series Base Edge Assemblies{6523, 6803, 6805} Convert the Buckets from the J-Series Base Edge Assemblies to the K-Series Base Edge Assemblies{6523, 6803, 6805}
587T Pipelayer Fuses and Circuit Breakers - Replace/Reset
587R Pipelayer Fuel Tank Water and Sediment - Drain
Instructions for Installing a Felling Head Arrangement{6000, 6319} Instructions for Installing a Felling Head Arrangement{6000, 6319}
583T Pipelayer Machine Systems Main Control Valve - Install
583T Pipelayer Machine Systems Main Control Valve - Remove
583T Pipelayer Machine Systems Main Control Valve - Assemble
583T Pipelayer Machine Systems Main Control Valve - Disassemble
777E and 777F Off-Highway Truck Power Train Transmission Hydraulic Control
24M Motor Grader Machine Systems Lubrication Injectors - Check and Adjust
587R Pipelayer Hydraulic System Oil - Change
C7 Engines for Caterpillar Built Machines Vibration Damper
793F and 793F CMD Off-Highway Truck Power Train Modulating Valve (Transmission Hydraulic Control)
572R Series 2, 583T, 587T, PL83 and PL87 Pipelayers Event Code List
587T Pipelayer Hydraulic System Oil Level - Check
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 1471 - FMI 04
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 1471 - FMI 08
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer CID 0267 FMI 02 Incorrect Engine Shutdown Switch inputs
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 2150 - FMI 03
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer E363 High Fuel Supply Temperature
RM-300 Reclaimer Mixer Power Train Piston Motor (Front Propel) - Remove