Cylinder Head
Show/hide table
| |
| Illustration 1 | g06267774 |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| - | - | - | Use the following procedure in order to tighten the cylinder head bolts using Multiple-Spindle torque driver:
1. Before assembly, lubricate the bolts with clean engine oil. 2. Tighten the bolts (1) through bolt (26) in a numerical sequence to 3. Loosen the bolts (1) through bolt (26) in a numerical sequence to 4. Tighten the bolts (1) through bolt (26) in a numerical sequence to 5. Turn the bolts (1) through bolt (26) in a numerical sequence to an angle of 90 degrees. 6. Repeat the steps 2 to 4. 7. Tighten the bolts (27) through bolt (31) to Use the following procedure in order to tighten the cylinder head bolts using hand torque wrench: 1. Before assembly, lubricate the bolts with clean engine oil. 2. Tighten the bolts (1) through bolt (26) in a numerical sequence to 3. Re-Tighten the bolts (1) through bolt (26) in a numerical sequence to 4. Turn the bolts (1) through bolt (26) in a numerical sequence to an angle of 90 degrees . 5. Repeat the steps 1 to 3. 6. Tighten the bolts (27) through bolt (31) to |
| B | - | - | Apply 6V-6640 Sealant to the bores for the cup plug prior to assembly.
The cup plug is measured from the head face to the top edge of the plug. Depth of installation Height of new cylinder head The flatness of the cylinder head should be within |
Caterpillar Information System:
Convert the Buckets from the J-Series Base Edge Assemblies to the K-Series Base Edge Assemblies{6523, 6803, 6805} Convert the Buckets from the J-Series Base Edge Assemblies to the K-Series Base Edge Assemblies{6523, 6803, 6805}
587T Pipelayer Fuses and Circuit Breakers - Replace/Reset
587R Pipelayer Fuel Tank Water and Sediment - Drain
Instructions for Installing a Felling Head Arrangement{6000, 6319} Instructions for Installing a Felling Head Arrangement{6000, 6319}
583T Pipelayer Machine Systems Main Control Valve - Install
583T Pipelayer Machine Systems Main Control Valve - Remove
583T Pipelayer Machine Systems Main Control Valve - Assemble
583T Pipelayer Machine Systems Main Control Valve - Disassemble
777E and 777F Off-Highway Truck Power Train Transmission Hydraulic Control
587T Pipelayer Fuel Tank Cap and Strainer - Clean
587T Pipelayer Fuel System Secondary Filter - Replace
587T Pipelayer Fuel System - Prime
C15 and C18 Generator Set Engines Engine - Install
24M Motor Grader Braking and Hydraulic Fan System Piston Pump (Brake, Hydraulic Fan) Margin Pressure - Test and Adjust
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Transmission (Power Shift) - Install
24M Motor Grader Machine Systems Lubrication Injectors - Check and Adjust
587R Pipelayer Hydraulic System Oil - Change
C7 Engines for Caterpillar Built Machines Vibration Damper
793F and 793F CMD Off-Highway Truck Power Train Modulating Valve (Transmission Hydraulic Control)
572R Series 2, 583T, 587T, PL83 and PL87 Pipelayers Event Code List
587T Pipelayer Hydraulic System Oil Level - Check
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 1471 - FMI 04
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System MID 082 - CID 1471 - FMI 08
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer CID 0267 FMI 02 Incorrect Engine Shutdown Switch inputs