Main Control Valve - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | FT-1114     | Vacuum Cap     | 1     |
5P-0306 | Vacuum Transducer     | 1     | |
6V-4142 | Fitting     | 1     | |
5K-5068 | Fitting     | 1     | |
B     | 138-7575     | Link Bracket     | 1     |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- If necessary, position main control valve (11) on mounting bracket (16) and install bolts (15) .
Show/hide table
Illustration 1 | g01244310 |
- Connect tube assemblies (14) .
- Use Tooling (B) and a suitable lifting device to position main control valve (11) on the machine. The weight of main control valve (11) is approximately 57 kg (125 lb).
Show/hide table
Illustration 2 | g01244308 |
- Connect hose assemblies (13) .
Show/hide table
Illustration 3 | g01244307 |
- Reposition main control valve (11) and install bolts (12) .
Show/hide table
Illustration 4 | g01244285 |
- Connect hose assemblies (10) .
Show/hide table
Illustration 5 | g01244284 |
- Connect hose assemblies (9), coupling (7), hose assembly (8), and hose assembly (6) .
Show/hide table
Illustration 6 | g01244283 |
- Connect hose assemblies (5) .
Show/hide table
Illustration 7 | g01244282 |
- Connect hose assemblies (4) and harness assemblies (3) .
Show/hide table
Illustration 8 | g01244281 |
- Install cable straps (2) .
- Install cover (1) .
Show/hide table
Illustration 9 | g01244280 |
- Remove Tooling (A) from the hydraulic tank.
Show/hide table
Illustration 10 | g01238830 |
Caterpillar Information System:
583T Pipelayer Machine Systems Main Control Valve - Remove
583T Pipelayer Machine Systems Main Control Valve - Assemble
583T Pipelayer Machine Systems Main Control Valve - Disassemble
777E and 777F Off-Highway Truck Power Train Transmission Hydraulic Control
587T Pipelayer Fuel Tank Cap and Strainer - Clean
587T Pipelayer Fuel System Secondary Filter - Replace
587T Pipelayer Fuel System - Prime
C15 and C18 Generator Set Engines Engine - Remove
CD54 Paving Compactor Water Spray Nozzles - Clean
621H OEM Wheel Tractor (Tier 4) Power Train Relief Valve (Transmission Lubrication)
773F and 775F Off-Highway Truck Service Ports
587T Pipelayer Ether Starting Aid Cylinder - Replace
Instructions for Installing a Felling Head Arrangement{6000, 6319} Instructions for Installing a Felling Head Arrangement{6000, 6319}
587R Pipelayer Fuel Tank Water and Sediment - Drain
587T Pipelayer Fuses and Circuit Breakers - Replace/Reset
Convert the Buckets from the J-Series Base Edge Assemblies to the K-Series Base Edge Assemblies{6523, 6803, 6805} Convert the Buckets from the J-Series Base Edge Assemblies to the K-Series Base Edge Assemblies{6523, 6803, 6805}
C9.3 Engine for Caterpillar Built Machines Cylinder Head
C15 and C18 Generator Set Engines Engine - Install
24M Motor Grader Braking and Hydraulic Fan System Piston Pump (Brake, Hydraulic Fan) Margin Pressure - Test and Adjust
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Transmission (Power Shift) - Install
24M Motor Grader Machine Systems Lubrication Injectors - Check and Adjust
587R Pipelayer Hydraulic System Oil - Change
C7 Engines for Caterpillar Built Machines Vibration Damper
793F and 793F CMD Off-Highway Truck Power Train Modulating Valve (Transmission Hydraulic Control)