Final Drive Planetary Carrier (In Chassis) - Remove - Right and Left Side
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Description     | Qty     |
A     | 1P-0068     | Cone     | 1     |
1P-0069 | Head     | 1     | |
1P-0071 | Jaw     | 3     | |
8K-8466 | Stud     | 1     | |
1A-8285 | Nut     | 3     | |
6H-0187 | Bolt     | 3     | |
1P-5546 | Block     | 1     | |
5P-8247 | Washer     | 1     | |
1B-4206 | Nut     | 1     | |
B     | 3B-2968     | Bolt     | 3     |
C     | 5P-8622     | Shackle     | 1     |
8T-3207 | Lifting Bracket     | 1     | |
1A-8063 | Bolt     | 2     | |
5P-8248 | Washer     | 6     | |
1B-4331 | Nut     | 2     |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- The following procedure is for the right side of the machine.
- Lower the counterweight. Refer to Operation and Maintenance Manual, "Counterweight Control" for the correct procedure.
- The following procedure is for the left side of the machine.
- Attach a suitable lifting device to ladder assembly (2). The weight of ladder assembly (2) is approximately 27 kg (60 lb). Remove clamps (1), bolts (3), and the washers. Remove ladder assembly (2) .
Show/hide table
Illustration 1 | g01239397 |
- Drain the final drive. Refer to Operation and Maintenance Manual, "Final Drive Oil Change".
Show/hide table
Illustration 2 | g01239398 |
Show/hide table
Illustration 3 | g01239406 |
- Remove the outer axle. Refer to Disassembly and Assembly, "Axle - Remove".
- Install Tooling (A) in order to hold sun gear (6) in place.
- Remove three equally spaced bolts (5) that hold planetary carrier (4) to the hub and install Tooling (B). Remove remaining bolts (5) .
Note: Tooling (B) must be installed to a depth of 25 mm (1.0 inch) in order to hold planetary carrier (4) .
- Adjust Tooling (C) so that Dimension (X) measures 145 mm (5.7 inch) and install Tooling (C) to planetary carrier (4) .
- Attach a suitable lifting device to Tooling (C). The weight of planetary carrier (4) is approximately 209 kg (461 lb).
- Use a pry bar in order to pull planetary carrier (4) away from the hub.
- Remove Tooling (B) .
- Remove planetary carrier (4) .
- Remove O-ring seals (7) and (8) .
Show/hide table
Illustration 4 | g01239417 |
- Hold sun gear (6) so that sun gear (6) does not fall. Remove Tooling (A) from planetary carrier (4) .
- Remove thrust ring (9) .
Show/hide table
Illustration 5 | g01239422 |
- Remove lip seal (10) .
Show/hide table
Illustration 6 | g01239424 |
- Repeat Steps 3 through 15 for the planetary carrier on the opposite side of the machine.
Caterpillar Information System:
C15 and C18 Generator Set Engines Gear Group (Front) - Install
583T Pipelayer Power Train Final Drive - Install - Right and Left Side
24M Motor Grader Power Train Torque Converter
M325D and M330D Excavators Power Train Electronic Control System MID 027 - CID 0298 - FMI 03
Clarification of Vertical Method Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220} Clarification of Vertical Method Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220}
587R Pipelayer Cooling System Coolant Extender (ELC) - Add
587R Pipelayer Hydraulic System Piston Pump (Implement)
TH350B, TH360B, TH460B and TH560B Telehandlers Machine Systems Piston Pump (Implement and Steering)
TH350B, TH360B, TH460B and TH560B Telehandlers Machine Systems Piston Pump (Implement and Steering)
583T Pipelayer Power Train Final Drive - Remove - Right and Left Side
C15 and C18 Generator Set Engines Gear Group (Front) - Remove
C15 and C18 Generator Set Engines Front Cover - Install
AS2302 Vers-A-Mat Asphalt Screed Screed Heat Control
AS2302 Vers-A-Mat Asphalt Screed Screed Extensions
CD54 Paving Compactor Fuses - Replace
C15 and C18 Generator Set Engines Housing (Front) - Remove
24M Motor Grader Machine Systems Battery
583T Pipelayer Power Train Final Drive Planetary Carrier (In Chassis) - Install - Right and Left Side
C15 and C18 Generator Set Engines Housing (Front) - Install
2006/02/13 New Hood Hinge Pins for Medium Wheel Loaders {7251}
2006/02/13 Change to Fan Shroud Increases Clearance {1353, 7272}
587R Pipelayer Towing the Machine
R1700G Load Haul Dump Machine Systems Tilt Cylinder - Remove
R1700G Load Haul Dump Power Train Axle Shaft - Remove