Final Drive - Remove - Right and Left Side
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Description | Qty |
| A | 8T-3207 | Lifting Bracket | 1 |
| 5P-8622 | Shackle | 1 | |
| 1D-4615 | Bolt | 2 | |
| 1B-4331 | Nut | 2 | |
| 5P-8248 | Washer | 4 | |
Start By:
- Separate the track. Refer to Disassembly and Assembly, "Track - Separate".
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the oil from the final drive. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change".
- Remove the outer drive axle. Refer to Disassembly and Assembly, "Axle - Remove".
- Repeat Steps 1 and 2 for the opposite side.
- The following procedure is for the right side of the machine.
- Lower the counterweight. Refer to Operation and Maintenance Manual, "Counterweight Control" for the correct procedure.
- The following procedure is for the left side of the machine.
- Attach a suitable lifting device to ladder assembly (2). The weight of ladder assembly (2) is approximately 27 kg (60 lb). Remove clamps (1), bolts (3), and the washers. Remove ladder assembly (2) .
Show/hide table
 | |
| Illustration 1 | g01239293 |
- Adjust Tooling (A) until Dimension (X) is equal to 145 mm (5.7 inch).
Show/hide table
 | |
| Illustration 2 | g01239295 |
- Remove two bolts (5) and install Tooling (A) to final drive (4). Attach a suitable lifting device to Tooling (A). The weight of final drive (4) is approximately 670 kg (1480 lb).
Show/hide table
 | |
| Illustration 3 | g01239297 |
Show/hide table
 | |
| Illustration 4 | g01239298 |
- Remove bolts (6) and (7). Do not remove bolts (8) .
- Remove final drive (4) and the O-ring seal.
- Repeat Steps 6 through 9 for the opposite side.
Caterpillar Information System:
C15 and C18 Generator Set Engines Gear Group (Front) - Remove
C15 and C18 Generator Set Engines Front Cover - Install
C15 and C18 Generator Set Engines Front Cover - Remove
AS2302 Vers-A-Mat Asphalt Screed Plate Locations and Film Locations
AS2302 Vers-A-Mat Asphalt Screed Specifications
24M Motor Grader Machine Systems Circle
24M Motor Grader Power Train Output Transfer Gear and Case
587R Pipelayer Power Train Troubleshooting
M325D L MH and M325D MH Material Handlers Hydraulic System Relief Valve (Pilot) - Test and Adjust
R1700G Load Haul Dump Power Train Axle Shaft - Install
2006/02/13 Barrel Adapter Allows Technician to Attach Filter Unit to Barrel {0645, 0680}
R1700G Load Haul Dump C11 Engine Supplement Hood - Remove
TH350B, TH360B, TH460B and TH560B Telehandlers Machine Systems Piston Pump (Implement and Steering)
TH350B, TH360B, TH460B and TH560B Telehandlers Machine Systems Piston Pump (Implement and Steering)
587R Pipelayer Hydraulic System Piston Pump (Implement)
587R Pipelayer Cooling System Coolant Extender (ELC) - Add
Clarification of Vertical Method Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220} Clarification of Vertical Method Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220}
M325D and M330D Excavators Power Train Electronic Control System MID 027 - CID 0298 - FMI 03
24M Motor Grader Power Train Torque Converter
583T Pipelayer Power Train Final Drive - Install - Right and Left Side
C15 and C18 Generator Set Engines Gear Group (Front) - Install
583T Pipelayer Power Train Final Drive Planetary Carrier (In Chassis) - Remove - Right and Left Side
AS2302 Vers-A-Mat Asphalt Screed Screed Heat Control
AS2302 Vers-A-Mat Asphalt Screed Screed Extensions