Final Drive - Install - Right and Left Side
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Description     | Qty     |
A     | 8T-3207     | Lifting Bracket     | 1     |
5P-8622 | Shackle     | 1     | |
1D-4615 | Bolt     | 2     | |
1B-4331 | Nut     | 2     | |
5P-8248 | Washer     | 4     |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Adjust Tooling (A) until Dimension (X) is equal to 145 mm (5.7 inch).
Show/hide table
Illustration 1 | g01239295 |
Show/hide table
Illustration 2 | g01239297 |
Show/hide table
Illustration 3 | g01239298 |
- Remove two bolts (5) and install Tooling (A) to final drive (4). Attach a suitable lifting device to Tooling (A). The weight of final drive (4) is approximately 670 kg (1480 lb). Position final drive (4) and the O-ring seal.
- Install bolts (6). Tighten bolts (6) to a torque of 800 ± 90 N·m (590 ± 66 lb ft). Install bolts (7) .
- Remove Tooling (A). Apply SAE 30W oil to the threads of two bolts (5). Tighten bolts (5) to a torque of 300 ± 50 N·m (221 ± 37 lb ft). Tighten bolts (5) for another 1/3 turn. The final torque for bolts (5) must be a minimum of 570 N·m (420 lb ft).
- Refer to Steps 1 through 4 for the opposite side.
- The following procedure is for the left side of the machine.
- Use a suitable lifting device in order to position ladder assembly (2) to the original position. The weight of ladder assembly (2) is approximately 27 kg (60 lb). Install bolts (3), the washers, and clamps (1) .
Show/hide tableIllustration 4 g01239293
- The following procedure is for the right side of the machine.
- Raise the counterweight. Refer to Operation and Maintenance Manual, "Counterweight Control" for the correct procedure.
- Install the outer drive axle. Refer to Disassembly and Assembly, "Axle - Install".
- Fill the final drive with oil. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change".
- Refer to Steps 8 and 9 for the opposite side.
End By: Connect the track. Refer to Disassembly and Assembly, "Track - Connect".
Caterpillar Information System:
24M Motor Grader Power Train Torque Converter
M325D and M330D Excavators Power Train Electronic Control System MID 027 - CID 0298 - FMI 03
Clarification of Vertical Method Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220} Clarification of Vertical Method Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220}
587R Pipelayer Cooling System Coolant Extender (ELC) - Add
587R Pipelayer Hydraulic System Piston Pump (Implement)
TH350B, TH360B, TH460B and TH560B Telehandlers Machine Systems Piston Pump (Implement and Steering)
TH350B, TH360B, TH460B and TH560B Telehandlers Machine Systems Piston Pump (Implement and Steering)
583T Pipelayer Power Train Final Drive - Remove - Right and Left Side
C15 and C18 Generator Set Engines Gear Group (Front) - Remove
C15 and C18 Generator Set Engines Front Cover - Install
C15 and C18 Generator Set Engines Front Cover - Remove
AS2302 Vers-A-Mat Asphalt Screed Plate Locations and Film Locations
C15 and C18 Generator Set Engines Gear Group (Front) - Install
583T Pipelayer Power Train Final Drive Planetary Carrier (In Chassis) - Remove - Right and Left Side
AS2302 Vers-A-Mat Asphalt Screed Screed Heat Control
AS2302 Vers-A-Mat Asphalt Screed Screed Extensions
CD54 Paving Compactor Fuses - Replace
C15 and C18 Generator Set Engines Housing (Front) - Remove
24M Motor Grader Machine Systems Battery
583T Pipelayer Power Train Final Drive Planetary Carrier (In Chassis) - Install - Right and Left Side
C15 and C18 Generator Set Engines Housing (Front) - Install
2006/02/13 New Hood Hinge Pins for Medium Wheel Loaders {7251}
2006/02/13 Change to Fan Shroud Increases Clearance {1353, 7272}
587R Pipelayer Towing the Machine