Axle Shaft - Remove
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-7407 | Eyebolt | 1 |
Start By:
- Install steering frame lock pin. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Move the machine until drain plug (3) is in the DOWNWARD position. Remove drain plug (3) and drain the oil into a suitable container.
- Remove six bolts (1), the washers, and cover assembly (2).
Show/hide table
Illustration 2 g01239552 - Remove O-ring seal (4).
Show/hide table
Illustration 3 g01239561 - Install Tooling (A) in the end of axle shaft (5). Using Tooling (A), pull axle shaft (5) from the final drive by approximately
500 mm (20 inch) . - Attach a hoist and a suitable lifting device to axle shaft (5).
- Remove axle shaft (5). The weight of the axle shaft is approximately
38 kg (84 lb) .Show/hide tableIllustration 4 g06156699 - Remove retaining ring (8), sun gear (6), and thrust washer (7) from axle shaft (5).
Note: Take note of the orientation of thrust washer (7) for assembly purposes.
Show/hide table
Illustration 1 | g01239554 |
Caterpillar Information System:
R1700G Load Haul Dump Machine Systems Tilt Cylinder - Remove
587R Pipelayer Towing the Machine
2006/02/13 Change to Fan Shroud Increases Clearance {1353, 7272}
2006/02/13 New Hood Hinge Pins for Medium Wheel Loaders {7251}
C15 and C18 Generator Set Engines Housing (Front) - Install
583T Pipelayer Power Train Final Drive Planetary Carrier (In Chassis) - Install - Right and Left Side
24M Motor Grader Machine Systems Battery
C15 and C18 Generator Set Engines Housing (Front) - Remove
CD54 Paving Compactor Fuses - Replace
AS2302 Vers-A-Mat Asphalt Screed Screed Extensions
AS2302 Vers-A-Mat Asphalt Screed Screed Heat Control
583T Pipelayer Power Train Final Drive Planetary Carrier (In Chassis) - Remove - Right and Left Side
R1700G Load Haul Dump Power Train Trunnion Support (Oscillating Axle, Rear) - Install
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0005 FMI 02
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0005 FMI 05
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0005 FMI 06
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0005 FMI 07
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0006 FMI 02
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0006 FMI 05
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0006 FMI 06
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0006 FMI 07
M325D and M330D Excavators Machine Electronic Control System System Schematic
583T Pipelayer Machine Systems Auxiliary Hydraulic Pump - Remove
583T Pipelayer Machine Systems Auxiliary Hydraulic Pump - Install