Trunnion Support (Oscillating Axle, Rear) - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
B | 8T-3099 | Installer | 1 |
C | CAT Advanced 3 Moly Grease | 1 | |
D | High strength/ high temp. anaerobic flange sealant | 1 |
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
- Use Tooling (B) and a press to install sleeve bearing (11).
Show/hide table
Illustration 3 g01239106 - Install O-ring seal (10).
- Apply Tooling (C) to sleeve bearing (11) and O-ring seal (10).
Show/hide table
Illustration 4 g01238727 - Attach a hoist and a suitable lifting device to trunnion (9).
- Install trunnion (9). The weight of the trunnion is approximately
56 kg (123 lb) . - Install 16 bolts (8) and the washers. Tighten the bolts to a torque of
530 ± 70 N·m (390 ± 50 lb ft) .Show/hide tableIllustration 5 g01239981 - Attach a hoist and suitable lifting device to rear trunnion support (3).
- Install rear trunnion support (3) to trunnion (9). The weight of the rear trunnion support is approximately
113 kg (250 lb) .Show/hide tableIllustration 6 g01238723 - Apply Tooling (C) to thrust bearing (7). Install thrust bearing (7).
Show/hide table
Illustration 7 g01238721 - Install plate (6) and ten bolts (5). Tighten the bolts to a torque of
530 ± 70 N·m (390 ± 50 lb ft) .Show/hide tableIllustration 8 g01238719 - Apply Tooling (C) to thrust bearing (4). Install thrust bearing (4).
Show/hide table
Illustration 9 g01238718 - Apply Tooling (D) to the mating surfaces of rear trunnion support (3) and cover (2). Install cover (2), ten bolts (1) and the washers. The weight of the cover is approximately
22 kg (49 lb) . Tighten the bolts to a torque of530 ± 70 N·m (390 ± 50 lb ft) .
Show/hide table
Illustration 1 | g01239114 |
Show/hide table
Illustration 2 | g01239116 |
Caterpillar Information System:
R1700G Load Haul Dump Power Train Axle Shaft - Remove
R1700G Load Haul Dump Machine Systems Tilt Cylinder - Remove
587R Pipelayer Towing the Machine
2006/02/13 Change to Fan Shroud Increases Clearance {1353, 7272}
2006/02/13 New Hood Hinge Pins for Medium Wheel Loaders {7251}
C15 and C18 Generator Set Engines Housing (Front) - Install
583T Pipelayer Power Train Final Drive Planetary Carrier (In Chassis) - Install - Right and Left Side
24M Motor Grader Machine Systems Battery
C15 and C18 Generator Set Engines Housing (Front) - Remove
CD54 Paving Compactor Fuses - Replace
AS2302 Vers-A-Mat Asphalt Screed Screed Extensions
AS2302 Vers-A-Mat Asphalt Screed Screed Heat Control
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0005 FMI 02
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0005 FMI 05
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0005 FMI 06
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0005 FMI 07
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0006 FMI 02
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0006 FMI 05
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0006 FMI 06
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0006 FMI 07
M325D and M330D Excavators Machine Electronic Control System System Schematic
583T Pipelayer Machine Systems Auxiliary Hydraulic Pump - Remove
583T Pipelayer Machine Systems Auxiliary Hydraulic Pump - Install
583T Pipelayer Machine Systems Steering Pump - Remove