Exhaust Purifier and Muffler - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | -     | Loctite 596     | -     |
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
- Apply Tooling (A) to the inside surface of the muffler mount.
Show/hide table
Illustration 1 | g01279361 |
- Attach a suitable lifting device to exhaust purifier and muffler (7) .
Show/hide table
Illustration 2 | g01238706 |
- Install exhaust purifier and muffler (7) in position.
- Install gasket (6) .
- Install tube assembly (4) and three bolts (5) .
Show/hide table
Illustration 3 | g01238682 |
- Install clamp (3) in the position recorded in the removal procedure. Tighten clamp (3) .
Show/hide table
Illustration 4 | g01238679 |
- Install cover (2) .
- Install cover (1) .
Show/hide table
Illustration 5 | g01238301 |
End By: Remove the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Caterpillar Information System:
572R Series 2, 583T, 587T, PL83 and PL87 Pipelayers Transmission - 583T PL83 587T And PL87
Clarification of Lift + Cross Slope Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220} Clarification of Lift + Cross Slope Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220}
572R Series 2, 583T, 587T, PL83 and PL87 Pipelayers Implement System - 583T 587T PL83 And PL87
RM-300 Reclaimer Mixer Machine Systems Chain Drive (Rotor) - Remove and Install
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Throttle Position Sensor Circuit - Test
C15 and C18 Generator Set Engines Crankshaft Front Seal - Install
777F Off-Highway Truck Hydraulic System Hydraulic and Transmission Tank (Torque Converter, Hoist, Brake)
RM-300 Reclaimer Mixer Machine Systems Oil Tank (Rotor Drive Lubrication) - Remove and Install
2006/03/20 Three Seal Installers Available for Servicing Hand Metering Units {0732, 4312}
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Engine Shutdown Switch Circuit - Test
583T Pipelayer Hydraulic System Gear Pump (Fan, Counterweight)
583T Pipelayer Power Train Drive Axle - Remove and Install
RM-300 Reclaimer Mixer Machine Systems Rotor Stub Shaft - Disassemble
R1700G Load Haul Dump Machine Systems Ejector Bucket - Disassemble
R1700G Load Haul Dump Machine Systems Ejector Bucket - Assemble
R1700G Load Haul Dump C11 Engine Supplement Hood - Remove
2006/02/13 Barrel Adapter Allows Technician to Attach Filter Unit to Barrel {0645, 0680}
R1700G Load Haul Dump Power Train Axle Shaft - Install
M325D L MH and M325D MH Material Handlers Hydraulic System Relief Valve (Pilot) - Test and Adjust
587R Pipelayer Power Train Troubleshooting
24M Motor Grader Power Train Output Transfer Gear and Case
24M Motor Grader Machine Systems Circle
AS2302 Vers-A-Mat Asphalt Screed Specifications
AS2302 Vers-A-Mat Asphalt Screed Plate Locations and Film Locations