Crankshaft Front Seal - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
D     | 5P-1733     | 密封定位器     | 1     |
E     | 5P-1737     | 螺栓     | 3     |
F     | 9S-8858     | 螺母 (密封安装工具)     | 1     |
G     | 6V-6142     | 密封安装工具     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 必须同时更换曲轴前密封和承磨衬套。 一旦曲轴前密封与承磨衬套分开,不得再次使用这些部件。
- 在安装曲轴前密封和承磨衬套之前,请检查曲轴有无划痕。 此外,请检查曲轴表面是否有无可能引起失圆状况的变形。 使用抛光布以清除曲轴上的瑕疵。
注: 在安装曲轴前密封和承磨衬套的过程中,请勿使用任何类型的润滑剂。
- 清洁曲轴外径。
- 使用工具 (E) 将工具 (D) 固定到曲轴上.
Show/hide table
图 1 | g01635200 |
- 将承磨衬套 (2) 和曲轴前密封 (1) 安置在工具 (D) 上。 将工具 (G) 安装在工具 (D) 上。 润滑工具 (F) 上的垫圈表面。 将工具 (F) 安装在工具 (D) 上。
注: 把曲轴前密封安装到发动机中,并使指示曲轴转动方向的箭头指向发动机前方。
- 拧紧工具 (F) 直到工具 (G) 接触到工具 (D) 。
- 将工具 (F) 和工具 (G) 从工具 (D) 上拆下。
- 将工具 (E) 和工具 (D) 从曲轴上拆下。
End By: 安装减振器和皮带轮。 请参阅 拆解和组装, "减振器和皮带轮 - 拆卸和安装"。
Caterpillar Information System:
777F Off-Highway Truck Hydraulic System Hydraulic and Transmission Tank (Torque Converter, Hoist, Brake)
RM-300 Reclaimer Mixer Machine Systems Oil Tank (Rotor Drive Lubrication) - Remove and Install
2006/03/20 Three Seal Installers Available for Servicing Hand Metering Units {0732, 4312}
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Engine Shutdown Switch Circuit - Test
583T Pipelayer Hydraulic System Gear Pump (Fan, Counterweight)
583T Pipelayer Power Train Drive Axle - Remove and Install
583T Pipelayer Machine Systems Auxiliary Hydraulic Pump - Assemble
583T Pipelayer Machine Systems Auxiliary Hydraulic Pump - Disassemble
583T Pipelayer Machine Systems Steering Pump - Assemble
583T Pipelayer Machine Systems Steering Pump - Disassemble
572R Series 2, 583T, 587T, PL83 and PL87 Pipelayers Transmission Clutch - 583T PL83 587T And PL87
Payload Control System (PCS) 2.X System Schematic
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Throttle Position Sensor Circuit - Test
RM-300 Reclaimer Mixer Machine Systems Chain Drive (Rotor) - Remove and Install
572R Series 2, 583T, 587T, PL83 and PL87 Pipelayers Implement System - 583T 587T PL83 And PL87
Clarification of Lift + Cross Slope Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220} Clarification of Lift + Cross Slope Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220}
572R Series 2, 583T, 587T, PL83 and PL87 Pipelayers Transmission - 583T PL83 587T And PL87
R1700G Load Haul Dump C11 Engine Supplement Exhaust Purifier and Muffler - Install
RM-300 Reclaimer Mixer Machine Systems Rotor Stub Shaft - Disassemble
R1700G Load Haul Dump Machine Systems Ejector Bucket - Disassemble
R1700G Load Haul Dump Machine Systems Ejector Bucket - Assemble
R1700G Load Haul Dump C11 Engine Supplement Hood - Remove
2006/02/13 Barrel Adapter Allows Technician to Attach Filter Unit to Barrel {0645, 0680}
R1700G Load Haul Dump Power Train Axle Shaft - Install