Drive Axle - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | FT1952 | Axle Removal Tool | 1 |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Remove bolts (1) and the washers. Remove cover (2) and the O-ring seal from final drive (3).
Show/hide table
Illustration 2 g01239043 - Remove retainer (4) from final drive (3).
Show/hide table
Illustration 3 g01239044 - Use Tooling (A) to remove outer axle (5) (not shown) from final drive (3).
Show/hide table
Illustration 4 g01239045 - Use Tooling (A) to remove inner axle (6) (not shown) from final drive (3).
- Repeat Steps 1 through 3 for the final drive on the opposite side of the machine.
Show/hide table
Illustration 1 | g01239032 |
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | FT1952 | Axle Removal Tool | 1 |
B | 369–9451 | Petro Gel Amber Grease | 1 |
- Start the engine and release the parking brake.
Show/hide table
Illustration 5 g06120222 Show/hide tableIllustration 6 g06120218 Show/hide tableIllustration 7 g06120210 - Apply Tooling (B) to the axles at locations (X).
Note: Remove all burrs from the axles before applying Tooling (B).
Show/hide tableIllustration 8 g01239045 - Use Tooling (A) to install inner axle (6) (not shown) to final drive (3).
Note: If the carrier is disengaged from the bevel gear shaft, slide the carrier on the bevel gear shaft as the inner axle is installed.
Show/hide tableIllustration 9 g01239044 - Use Tooling (A) to install outer axle (5) (not shown) to final drive (3).
Show/hide table
Illustration 10 g01239043 - Install retainer (4) to final drive (3).
- Repeat Steps 1 through 4 for the other side of the machine.
Show/hide table
Illustration 11 g01239032 - Position cover (2) and the O-ring seal to final drive (3). Install bolts (1) and the washers.
- Repeat Steps 4 through 7 for the final drive on the opposite side of the machine.
- Stop the engine.
- Check the oil levels. Refer to Operation and Maintenance Manual, "Final Drive Oil Level - Check" for the correct procedure.
Caterpillar Information System:
583T Pipelayer Machine Systems Auxiliary Hydraulic Pump - Assemble
583T Pipelayer Machine Systems Auxiliary Hydraulic Pump - Disassemble
583T Pipelayer Machine Systems Steering Pump - Assemble
583T Pipelayer Machine Systems Steering Pump - Disassemble
572R Series 2, 583T, 587T, PL83 and PL87 Pipelayers Transmission Clutch - 583T PL83 587T And PL87
Payload Control System (PCS) 2.X System Schematic
Payload Control System (PCS) 2.X Glossary of Electrical Terms
Payload Control System (PCS) 2.X Battery (Internal Backup) - Replace
Payload Control System (PCS) 2.X Position Sensor (Lift Linkage) - Adjust
Payload Control System (PCS) 2.X Payload Electronic Control Module - Replace
Payload Control System (PCS) 2.X MID 074 - CID 0820 - FMI 02
Payload Control System (PCS) 2.X MID 074 - CID 0817 - FMI 12
583T Pipelayer Hydraulic System Gear Pump (Fan, Counterweight)
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Engine Shutdown Switch Circuit - Test
2006/03/20 Three Seal Installers Available for Servicing Hand Metering Units {0732, 4312}
RM-300 Reclaimer Mixer Machine Systems Oil Tank (Rotor Drive Lubrication) - Remove and Install
777F Off-Highway Truck Hydraulic System Hydraulic and Transmission Tank (Torque Converter, Hoist, Brake)
C15 and C18 Generator Set Engines Crankshaft Front Seal - Install
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Throttle Position Sensor Circuit - Test
RM-300 Reclaimer Mixer Machine Systems Chain Drive (Rotor) - Remove and Install
572R Series 2, 583T, 587T, PL83 and PL87 Pipelayers Implement System - 583T 587T PL83 And PL87
Clarification of Lift + Cross Slope Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220} Clarification of Lift + Cross Slope Configuration in GPS/ATS AccuGrade TM Version 6.0 Software Operation for Motor Graders {7220}
572R Series 2, 583T, 587T, PL83 and PL87 Pipelayers Transmission - 583T PL83 587T And PL87
R1700G Load Haul Dump C11 Engine Supplement Exhaust Purifier and Muffler - Install