Auxiliary Water Pump - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 207-1601 | 橡胶润滑剂 | 1 |
- 使用工具 (A) 以将油封 (13) 安装到壳体组件 (3) 中。
- 安装螺塞 (16)。
Show/hide table
图 2 g03506096 - 将轴 (9)、止推垫圈 (8) 和螺栓 (7) 安装到壳体 (3) 中。
Show/hide table
图 3 g03505757 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将橡胶密封和陶瓷密封 (14) 安装到壳体 (3) 中。
注: 向轴倒角和密封作用面上涂覆一薄层工具 (A)。 避开陶瓷密封表面。
- 安装陶瓷密封 (13)、挡圈组件 (12) 和弹簧 (11)。
- 在安装叶轮 (10) 前,用干净的发动机机油稍稍涂抹轴。 将叶轮 (10) 安装到轴端部,深度为
0.00 ± 0.15 mm (0.00000 ± 0.00591 in) 。Show/hide table图 4 g03506363 - 冷却轴承 (11)。 将轴承 (11) 安装到壳体组件中。 确保轴承 (11 )中的机油孔与壳体组件 (X) 中的油道对齐。 必须将轴承 ( 11 )安装到深度
1.5 ± 0.5 mm (0.02 ± 0.02 in) 。 组装后,轴承 (11) 的内径必须为75.000 ± 0.055 mm (2.9527 ± 0.0022 in) 。 (11).Show/hide table图 5 g03505611 - 将塞 (4)、O 形密封圈、塞 (5) 和塞 (6) 安装到壳体 (3) 中。
Show/hide table
图 6 g03505607 - 用干净的发动机机油稍稍润滑接头 ( 2 )中的密封凹槽。 在接头 (2) 上安装 O 形密封圈。 将适配器 (2) 和螺栓 (1) 安装到壳体 (3) 上。
Show/hide table
图 1 | g03505898 |
结束:
- 安装辅助水泵。
Caterpillar Information System:
3500 Engines Auxiliary Water Pump - Disassemble
PM-201 Cold Planer Upper Conveyor Belt (Second Stage) Tension and Tracking - Adjust
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Hood and Engine Enclosure - Install
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Hood and Engine Enclosure - Remove
793D Off-Highway Truck/Tractor Electronic Control Module (Integrated Brake) - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Refrigerant Compressor - Remove and Install
Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736} Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736}
785D OEM Off-Highway Truck Machine Systems Electronic Control Module (Power Train) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Throttle Lock Switch Circuit - Test
R2900G Load Haul Dump Lifting and Tying Down the Machine
PM-201 Cold Planer Water Spray System Fluid Level - Check
PM-201 Cold Planer Water Spray System - Drain
PM-201 Cold Planer Upper Conveyor Lift Cylinder Mount - Lubricate
PM-201 Cold Planer Track Tension - Check/Adjust
PM-201 Cold Planer Propel System Track
PM-201 Cold Planer Rotor Service Door Cylinder Pins - Lubricate
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Left Propel) - Remove
PM-201 Cold Planer Propel System Idlers (Track)
PM-201 Cold Planer Rotor Drive Belt - Inspect
PM-201 Cold Planer Propel System Hydraulic Tank
PM-201 Cold Planer Propel System Track Adjuster and Recoil
PM-201 Cold Planer Rotor Cutter Bits - Inspect/Replace
793D Off-Highway Truck/Tractor Screen (Hoist Pump) - Remove
793D Off-Highway Truck/Tractor Screen (Hoist Pump) - Install