834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Caterpillar


Refrigerant Compressor - Remove and Install

Usage:

836H BXD

拆卸步骤

    ------ WARNING! ------

    接触制冷剂会使人受伤。

    此系统永远处于加压状态,即便发动机没有工作也是如此。 切勿让已加注制冷剂的系统受热。

    接触制冷剂会造成冻伤。 让手、脸避开有助于防止受伤。

    制冷管路打开时,须始终佩带护目镜,即便压力计显示系统中已经没有制冷剂,也须佩带。

    取下接头时务必小心谨慎。 慢慢地拧松接头。 如果此系统仍然有压力,请抽空系统,回收制冷剂,然后再拆下接头。

    通过点燃的香烟吸入制冷剂会导致人身伤害或死亡。

    通过点燃的香烟或其他抽烟方法吸入空调制冷气体,或吸入燃烧空调制冷气体形成的烟雾,都会导致人身伤害或死亡。

    维修空调时,或在任何可能存在制冷气体的情况下都不要抽烟。

    请先将机器移至平坦的地方,然后再对空调和加热系统进行检查。 把所有机具降到地面。 确保变速箱处于空档或停车位置,确保停车制动器接合。 让所有其他人员远离机器。


  1. 回收空调系统中的空调制冷剂。 请参阅维修手册, SENR5664, "使用 R-134a 制冷剂的空调与暖风系统",了解相关正确步骤。 请参阅专门出版物, NEDG5065, "空调工具"了解正确工具信息。



    图 1g01141390

  1. 打开检修门 (1) 。



    图 2g01141266

  1. 拆下螺栓 (2) 后将护罩组件 (3) 推到一边。



    图 3g01141267

  1. 拆下皮带 (4) 。 请参阅操作和保养手册, "皮带 - 检查 / 调整 / 更换"。 拆下螺栓 (5) 。 断开管子组件 (6) 。



    图 4g01141264

  1. 拆下螺栓 (7) 。 断开软管组件 (8) 。



    图 5g01141268

  1. 拆下螺栓 (9) 和制冷剂压缩机 (10) 。

安装步骤




    图 6g01141268

  1. 定位制冷剂压缩机 (10) ,然后安装螺栓 (9) 。



    图 7g01141264

  1. 连接软管组件 (8) 。 安装螺栓 (7) 。



    图 8g01141267

  1. 安装皮带 (4) 。 请参阅操作和保养手册, "皮带 - 检查 / 调整 / 更换"。 安装线束组件 (6) 。 安装螺栓 (5) 。



    图 9g01141266

  1. 将护罩组件 (3) 移动就位后安装螺栓 (2) 。



    图 10g01141390

  1. 关闭检修门 (1) 。

  1. 加注空调系统。 请参阅维修手册, SENR5664, "使用 R-134a 制冷剂的空调与暖风系统",了解相关正确步骤。 请参阅专门出版物, NEDG5065, "空调工具"了解正确工具信息。

Caterpillar Information System:

Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736} Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736}
785D OEM Off-Highway Truck Machine Systems Electronic Control Module (Power Train) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Throttle Lock Switch Circuit - Test
R2900G Load Haul Dump Lifting and Tying Down the Machine
PM-201 Cold Planer Water Spray System Fluid Level - Check
PM-201 Cold Planer Water Spray System - Drain
PM-201 Cold Planer Steering Cylinder Ends - Lubricate
PM-201 Cold Planer Steering Linkage - Lubricate
C11 and C15 Engines for Caterpillar Built Machines Compression Brake Solenoid Circuit - Test
PM-201 Cold Planer Legs (Struts) - Lubricate
PM-201 Cold Planer Rotor Service Door Pivot Pins - Lubricate
PM-201 Cold Planer Tracks - Inspect
793D Off-Highway Truck/Tractor Electronic Control Module (Integrated Brake) - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Hood and Engine Enclosure - Remove
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Hood and Engine Enclosure - Install
PM-201 Cold Planer Upper Conveyor Belt (Second Stage) Tension and Tracking - Adjust
3500 Engines Auxiliary Water Pump - Disassemble
3500 Engines Auxiliary Water Pump - Assemble
PM-201 Cold Planer Upper Conveyor Lift Cylinder Mount - Lubricate
PM-201 Cold Planer Track Tension - Check/Adjust
PM-201 Cold Planer Propel System Track
PM-201 Cold Planer Rotor Service Door Cylinder Pins - Lubricate
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Left Propel) - Remove
PM-201 Cold Planer Propel System Idlers (Track)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.