Hood and Engine Enclosure - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7573     | 连杆支架     | 1     |
开始:
- 拆下消音器。 请参阅拆解和组装, "消音器 - 拆卸和安装"。
- 将蓄电池断路开关转到断开位置。
- 排出发动机冷却液。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
- 打开检修门 (1) 。
Show/hide table
图 1 | g01141390 |
- 拆下螺栓 (2) 、 (4) 和 (5) 。 将轨道 (3) 从机器右侧拆下。
Show/hide table
图 2 | g01141282 |
- 卸下螺栓 (7) 和面板 (6) 。
Show/hide table
图 3 | g01141274 |
- 松开卡箍 (10) 后将软管 (8) 滑到管 (9) 上。 拆下螺栓 (11) 和防护罩组件 (12) 。 对另一侧重复上述步骤。
Show/hide table
图 4 | g01141280 |
- 断开软管 (14) 。 将线束组件 (15) 从辅助起动乙醚罐 (13) 和立柱组件 (16) 上断开。
Show/hide table
图 5 | g01141287 |
- 将适当的起吊设备固定到立柱组件 (16) 上。 拆下螺栓 (18) 。 作为一体拆下立柱组件 (16) 和检修门 (17) 。 立柱组件 (16) 和检修门 (17) 的总重量约为 32 kg (70 lb)。
Show/hide table
图 6 | g01141281 |
- 将软管组件 (20) 从用来固定空气滤清器维修指示器的立柱组件 (19) 上断开。 将适当的起吊设备固定到立柱组件 (19) 上。 拆下螺栓 (22) 。 作为一体拆下立柱组件 (19) 和检修门 (21) 。 立柱组件 (19) 和检修门 (21) 的总重量约为 34 kg (75 lb)。
Show/hide table
图 7 | g01141285 |
Show/hide table
图 8 | g01141276 |
- 由两人拆下侧面板 (23) 和 (24) 。 侧面板 (23) 的重量约为 36 kg (80 lb)。 侧面板 (24) 的重量约为 36 kg (80 lb)。
Show/hide table
图 9 | g01141286 |
- 断开线束组件 (25) 。
Show/hide table
图 10 | g01141275 |
- 打开检修门 (26) 。
Show/hide table
图 11 | g01141273 |
- 拆下螺栓 (27) ,然后拆下面板组件 (28) 。
Show/hide table
图 12 | g01141278 |
Show/hide table
图 13 | g01141277 |
- 将螺栓 (29) 和 (30) 从支撑组件 (31) 上拆下。 对机器两侧重复此过程。
Show/hide table
图 14 | g01141284 |
Show/hide table
图 15 | g01141283 |
- 将工具 (A) 和合适的起吊设备连接到支撑组件 (31) 。 拆下螺栓 (32) ,然后拆卸支撑组件 (31) 。 支撑组件 (31) 的重量约为 80 kg (175 lb)。
- 拆下螺栓 (33) 和薄板组件 (34) 。
Show/hide table
图 16 | g01141279 |
Caterpillar Information System:
793D Off-Highway Truck/Tractor Electronic Control Module (Integrated Brake) - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Refrigerant Compressor - Remove and Install
Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736} Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736}
785D OEM Off-Highway Truck Machine Systems Electronic Control Module (Power Train) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Throttle Lock Switch Circuit - Test
R2900G Load Haul Dump Lifting and Tying Down the Machine
PM-201 Cold Planer Water Spray System Fluid Level - Check
PM-201 Cold Planer Water Spray System - Drain
PM-201 Cold Planer Steering Cylinder Ends - Lubricate
PM-201 Cold Planer Steering Linkage - Lubricate
C11 and C15 Engines for Caterpillar Built Machines Compression Brake Solenoid Circuit - Test
PM-201 Cold Planer Legs (Struts) - Lubricate
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Hood and Engine Enclosure - Install
PM-201 Cold Planer Upper Conveyor Belt (Second Stage) Tension and Tracking - Adjust
3500 Engines Auxiliary Water Pump - Disassemble
3500 Engines Auxiliary Water Pump - Assemble
PM-201 Cold Planer Upper Conveyor Lift Cylinder Mount - Lubricate
PM-201 Cold Planer Track Tension - Check/Adjust
PM-201 Cold Planer Propel System Track
PM-201 Cold Planer Rotor Service Door Cylinder Pins - Lubricate
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Left Propel) - Remove
PM-201 Cold Planer Propel System Idlers (Track)
PM-201 Cold Planer Rotor Drive Belt - Inspect
PM-201 Cold Planer Propel System Hydraulic Tank